- 您現在的位置：買賣IC網 > PDF目錄376491 > AN7555 (Panasonic Corporation) BTL output power IC for car audio PDF資料下載
參數資料
| 型號： | AN7555 |
| 廠商： | Panasonic Corporation |
| 英文描述： | BTL output power IC for car audio |
| 中文描述： | BTL輸出的汽車音響電源IC |
| 文件頁數： | 4/5頁 |
| 文件大小： | 56K |
| 代理商： | AN7555 |
4
AN7555NZ
ICs for Audio Common Use
I
Usage Notes
1. Always attach an outside heat sink to use the AN7555NZ. In addition, the outside heat sink must be fastened onto
a chassis for use.
2. Connect the radiation fin to the GND potential.
3. Prevent short circuit to V
CC
and short circuit to GND, and load short-circuit although the protection circuits for short
circuit to V
CC
and ASO are built-in.
4. The thermal protection circuit gets actuated when T
j
=
approx. 150
°
C, but it is automatically reset when the chip
temperature drops below the above set level.
5. The overvoltage protection circuit starts the protection operation at V
CC
=
approx. 20 V.
6. Take into consideration the heat radiation design particularly when V
CC
is set high.
7. When the beep sound function is not used, connect to GND the beep sound input pin.
8. Don't down below
0.3 V for the beep sound input pin.
9. When the AUX function is not used, open the AUX input pin.
10. Connect to signal GND of pre-stage amplifier only for the signal source ground.
There are the possibility of breakdown for the following conditions.
1. Reverse connection of the power supply pin and the GND pin.
2. Connection of the power supply between output pins at open condition of the power supply pin and the GND pin.
3. Short circuit to GND of output pin when the GND pin is open.
4. Short circuit to GND of above the three output pins at the same time with a shorting resistor which does not
operate the protection circuit.
5. Short circuit to GND of above the plus and minus output pins at the same time with a shorting resistor which does
not operate the protection circuit.
6. Short circuit to ground with shorting the RF pin and the output pin.
I
Electrical Characteristics at V
CC
=
13.2 V, f
=
1 kHz, T
a
=
25
°
C (continued)
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Total harmonic distortion 2
THD2
V
IN
=
10 mV, f
IN
=
20 kHz, R
g
=
10
,
R
L
=
∞
V
IN
=
20 mV, R
L
=
4
V
IN
=
20 mV, R
L
=
4
V
IN
=
20 mV, R
L
=
4
,
G
V
=
1 dB (0 dB: 1 kHz)
0.1
0.5
%
Mute-on threshold voltage
MT
ON
4
V
Mute-off threshold voltage
MT
OFF
f
C
0.8
V
Cutoff frequency
20
40
kHz
Design reference data
Note) The characteristic values below are theoretical values for designing and not guaranteed.
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Maximum output power
P
Omax
Max. power, R
L
=
4
V
CC
=
14.4 V, THD
=
10%, R
L
=
4
V
CC
=
14.4 V, max. power, R
L
=
4
V
CC
=
14.4 V, THD
=
1%, R
L
=
4
,
PoL
=
3 dB (1 kHz: 0 dB)
V
CC
=
14.4 V, THD
=
1%, R
L
=
4
,
PoH
=
3 dB (1 kHz: 0 dB)
28
W
P
O2
21
P
Omax2
f
PL
34
Power band width
10
Hz
f
PH
18
kHz
STB threshold voltage
V
STB1
R
g
=
10 k
, R
L
=
4
, STB
→
ACT
R
g
=
10 k
, R
L
=
4
, ACT
→
STB
2.2
V
V
STB2
1.5
相關PDF資料 |
PDF描述 |
|---|---|
| AN7555NZ | BTL output power IC for car audio |
| AN7560 | BTL output power IC for car audio |
| AN7560Z | BTL output power IC for car audio |
| AN7561Z | BTL output power IC for car audio |
| AN7551Z | Power IC for BTL car audio |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AN7555NZ | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:BTL output power IC for car audio |
| AN7555Z | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:BTL output power IC for car audio |
| AN7555ZA-WLB | 制造商:Panasonic Industrial Company 功能描述:IC |
| AN-756 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Sampled Systems and the Effects of Clock Phase Noise and Jitter |
| AN7560 | 制造商:PANASONIC 制造商全稱:Panasonic Semiconductor 功能描述:BTL output power IC for car audio |
發布緊急采購，3分鐘左右您將得到回復。