ICs for CD/CD-ROM Player
AN8387S
V
CC
P
D
T
opr
T
stg
Supply Voltage
Power Dissipation
Operating Ambient Temperature
Storage Temperature
V
mW
C
C
Parameter
Symbol
Rating
10
1,200
Note)
–30 ~ +85
–55 ~ +125
Unit
Note) When mounted onto the glass epoxy PCB (50mm
×
50mm
×
0.8mm)
I
Absolute Maximum Ratings
(Ta=25C)
Parameter
Symbol
V
CC
P.V
CC
Range
3.5V ~ 9V
1.5V ~ 9V
Operating Supply Voltage Range
I
Recommended Operating Range
(Ta=25C)
Current Consumption at No Input (V
CC
)
Current Consumption at No Input (PV
CC
)
PV
CC
Leak Current
V
ref
Threshold (H)
Note 1)
V
ref
Threshold (L)
Note 2)
Input Amp. Input Impedance
Driver Input Offset Voltage
Note 3)
Driver Output Offset Voltage
Note 3)
Driver Dead Zone Width
Note3)
Driver Transfer Gain (+)
Note3)
Driver (+), (–) Transfer Gain Ratio
Note 3)
Driver Output Voltage
Driver Output Voltage Absolute Value
Driver Power Transistor Saturation
Voltage
PC Input Pin Threshold Voltage (H)
Note 4)
PC Input Pin Threshold Voltage (L)
Note 5)
Protective Diode Forward Voltage
Thermal Protective Circuit Operating
Temperature
I
VCCQ
I
PVCCQ
I
PVCCL
V
refH
V
refL
RA
IN
V
I offset
V
O offset
|V
DZ
|
G
+
RG
V
OLG
|V
OL
|
V
sat
V
PC THH
V
PC THL
V
PD
T
THD
V
CC
=9V, V
ref
=4.5V, PV
CC
=9V
V
CC
=9V, V
ref
=4.5V, PV
CC
=9V
V
CC
=
0V, V
ref
=
OPEN, PV
CC
=
10V
V
CC
=3V, PV
CC
=10V, V
IN
=0V
V
CC
=3V, PV
CC
=10V, V
IN
=0V
V
CC
=5V, V
=2.5V,
V
IN
=2.4
→
2.6V
V
CC
=9V, V
ref
=4.5V, PV
CC
=9V
V
CC
=9V, V
ref
=4.5V, PV
CC
=9V
V
CC
=9V, V
ref
=4.5V, PV
CC
=9V
V
CC
=9V, V
ref
=4.5V, PV
CC
=9V
V
CC
=9V, V
ref
=4.5V, PV
CC
=9V
V
CC
=9V, V
ref
=4.5V, PV
CC
=9V,
V
LIM
=0V
V
CC
=9V, V
ref
=4.5V, PV
CC
=9V,
V
LIM
=3V
V
CC
=9V, V
ref
=4.5V, PV
CC
=9V,
I
O
=300mA
V
CC
=9V, V
ref
=2.5V, PV
CC
=5V,
V
IN
=2.3V
V
CC
=9V, V
ref
=2.5V, PV
CC
=5V,
V
IN
=2.3V
1
0.7
1.45
0.75
–10
–55
–10
13
–1.9
–130
2.25
2.8
0.9
2
1.2
1
0
0
15.1
– 0.9
0.29
1.5
160
3.5
3.5
1
1
1.25
10
55
19
17
0.5
130
3
0.38
0.8
1.8
mA
mA
μ
A
V
V
k
mV
mV
mV
dB
dB
mV
V
V
V
V
V
C
Parameter
Symbol
Condition
min.
typ.
max.
Unit
I
Electrical Characteristics
(Ta=25C)
I
O
=300mA
Note1) V
voltage required to operate the driver.
Note2) If V
is made lower than this voltage, the driver dose not operate.
Note3) Refer to the driver input/output characteristics chart.
Note4) If the PC pin voltage is made higher than this voltage, there will be no output voltage from the driver. Both (+
) and (–)
outputs are pulling in the current.
Note5) If the PC pin voltage is made lower than this voltage, the driver operates normally.