- 您現在的位置：買賣IC網 > PDF目錄362372 > APA06Y04 HEADER,.1"ST MALE,1RW,2PIN, (10) .025"PST,.21"GOLDTAIL PDF資料下載
參數資料
| 型號： | APA06Y04 |
| 英文描述： | HEADER,.1"ST MALE,1RW,2PIN, (10) .025"PST,.21"GOLDTAIL |
| 中文描述： | 3，輸入電壓為5.5VDC，1.2Vdc - 20瓦的輸出為3.3V的DC - DC轉換器 |
| 文件頁數： | 12/15頁 |
| 文件大?。?/td> | 205K |
| 代理商： | APA06Y04 |
USA
1-760-930-4600
1-760-930-0698
Europe
44-(0)1384-842-211
44-(0)1384-843-355
Asia
852-2437-9662
852-2402-4426
TEL:
FAX:
www.astec.com
output also grounded.
3. Any non-SELV input must be provided with
reinforced from any other hazardous voltages,
including the ac mains, and must have a SELV
reliability test performed on it in combination
with the converters. Inputs must meet SELV
requirements.
If the input meets extra-low voltage (ELV)
requirements, then the converter's output is
considered ELV.
The input to these units is to be provided
with a maximum 10A normal blow fuse in
the ungrounded lead.
APA06G05(E-6) and APA6F05(E-6) need 15A
fuse.
Mechanical Considerations
Thermal Performance
APA06 series will derate at 55°C under the
condition of 200LFM. In order to maintain effi-
cient heat dissipation, the converters should be
mounted parallel with the air-flow direction.
Soldering
APA06 series converters are compatible with
standard wave soldering techniques. When
wave soldering, the converter pins should be
preheated for 20-30 seconds at 110°C, and
wave soldered at 260°C for less than 10 sec-
onds.
When hand soldering, the iron temperature
should be maintained at 425°C and applied to
the converter pins for less than 5 seconds.
Longer exposure can cause internal damage to
the converter. Cleaning can be performed with
cleaning solvent IPA or with water.
-12-
A
A
AP
P
PA
A
A0
0
06
6
6
N
N
No
o
on
n
n-
-
I
I
Is
s
so
o
ol
l
la
a
at
t
te
e
ed
d
d
P
P
Po
o
ow
w
we
e
er
r
r
S
S
SI
I
IP
P
Ps
s
s
3
3
3V
V
V-
-
5
5
5.
.
.5
5
5V
V
V
I
I
In
n
np
p
pu
u
ut
t
t,
,
,
1
1
1.
.
.2
2
2V
V
V-
-
3
3
3.
.
.3
3
3V
V
V
O
O
Ou
u
ut
t
tp
p
pu
u
ut
t
t,
,
,
9
9
9-
-
2
2
20
0
0W
O
O
Ou
u
ut
t
tp
p
pu
u
ut
t
t
63.5 (2.50)
48.3 (1.90)
7.1
(0.28)
Keep Out
J1-1
2.54
(0.100)
1.17 (0.046) Plated-through Hole
1.78 (0.070) Pad Size Both Sides
J2-6
2.79
(0.110)
8.38
(0.33)
9.1
(0.36)
Max. height
Fig.6 Recommended Hole Pattern
Mechanical Chart (Figure 7-9 next page)
Recommended Hole Pattern
Dimensions are in millimeters (inches). Component-side footprint.
相關PDF資料 |
PDF描述 |
|---|---|
| APA100-101 | Analog IC |
| APA100-102 | Analog IC |
| APA105-KJ-002 | Demo Boards are available to enable users to evaluate AMPSS㈢ modules. |
| APA105-KC-001 | Demo Boards are available to enable users to evaluate AMPSS㈢ modules. |
| APA105-KJ-001 | Demo Boards are available to enable users to evaluate AMPSS㈢ modules. |
相關代理商/技術參數 |
參數描述 |
|---|---|
| APA0710 | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:1.1W Mono Low-Voltage Audio Power Amplifier |
| APA0710K | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:1.1W Mono Low-Voltage Audio Power Amplifier |
| APA0710KI | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:1.1W Mono Low-Voltage Audio Power Amplifier |
| APA0710KI-TR | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:1.1W Mono Low-Voltage Audio Power Amplifier |
| APA0710KI-TRL | 制造商:ANPEC 制造商全稱:Anpec Electronics Coropration 功能描述:1.1W Mono Low-Voltage Audio Power Amplifier |
發布緊急采購，3分鐘左右您將得到回復。