- 您現在的位置：買賣IC網 > PDF目錄362374 > APC08Y03-9MA Non-Isolated DC/DC Power Module PDF資料下載
參數資料
| 型號： | APC08Y03-9MA |
| 英文描述： | Non-Isolated DC/DC Power Module |
| 中文描述： | 非隔離DC / DC電源模塊 |
| 文件頁數： | 8/23頁 |
| 文件大小： | 2632K |
| 代理商： | APC08Y03-9MA |
Technical Reference Note (APC08)
MODEL: APC08 SERIES
OCTOBER 4, 2004 - REVISION 03
SHEET 8 OF 23
Typical Application Circuit (Standard Pinout)
Recommended C1 is a low ESR (<100 mohms) 100 μF tantalum and C2 is a 1 μF ceramic or equivalent. Recommended
output decoupling capacitor C3 for –W models is 22 μF low ESR ceramic capacitor (at a min). For all other models, C3 can go
as low as 1 μF ceramic capacitor.
Figure 2. Typical Application Circuit.
Enable Pin (Standard configuration)
Pin P5 is functioned to enable the output voltage of a
module. If this pin is left open or connected to > 4.1Vdc
up to 14Vdc, the module is turned on. On the other hand,
if this pin is connected to ground or to a voltage potential
from 0 to 0.8Vdc, the module is turned off. The enable pin
can source current up to 60
μ
A max - suited for typical
open-collector transistors readily available in the market.
For TTL compatibility, Figure 3 shows a 7405 open
collector inverter IC utilized to function the Enable
feature. Other common chips that can do the function are
74S05; 74HCT05; non-inverting - 7407; 74S07; 74HC07.
If SMT packaging is preferred, Fairchild's Tiny Logic
NC7SZ05 or TI's Little Logic SN7SLVC1G06 comes in SOT23
or SC70 packages.
Special Feature Pins (Options):
Trim Function (-9):
Pin P4 is used for output voltage adjustment. The output voltage can be trimmed through an external resistor or through an
external DC supply as described in the succeeding sections.
Method 1: External Trim Resistor
.
By connecting an external resistor across P4 and P3 (Gnd), the voltage appearing on pin P2 (Vo) is adjusted to a higher value.
The output voltage of a module can be adjusted up to a maximum value of 3.3V (nominal) or 83% of the input voltage,
Figure 3. Output Voltage Enable function diagram.
相關PDF資料 |
PDF描述 |
|---|---|
| APC08Y03-J | Non-Isolated DC/DC Power Module |
| APC08Y03-W | Non-Isolated DC/DC Power Module |
| APC08Y08-9 | Non-Isolated DC/DC Power Module |
| APC08Y08-9MA | Non-Isolated DC/DC Power Module |
| APC08Y08-J | PWR CORD,3C,Y,TWIN END,4', 18AWG, |
相關代理商/技術參數 |
參數描述 |
|---|---|
| APC08Y03-9WJ | 制造商:Johnson Components 功能描述:83755 |
| APC08Y03-J | 功能描述:DC/DC轉換器 CONV DCDC 25W 3.3Vin RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| APC08Y03-JL | 功能描述:DC/DC轉換器 DC-DC 1-OUT 1.8V 8A 30W 7-Pin SMT RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| APC08Y03-W | 制造商:ASTEC 制造商全稱:Astec America, Inc 功能描述:Non-Isolated DC/DC Power Module |
| APC08Y08 | 制造商:ASTEC 制造商全稱:Astec America, Inc 功能描述:Non-Isolated DC/DC Power Module |
發(fā)布緊急采購，3分鐘左右您將得到回復。