- 您現在的位置：買賣IC網 > PDF目錄362374 > APC12F08-9J CHOKE,AXIAL,CONFORMAL,100uH, 5% INDUCTIVE TOL,275 IDC, PDF資料下載
參數資料
| 型號： | APC12F08-9J |
| 英文描述： | CHOKE,AXIAL,CONFORMAL,100uH, 5% INDUCTIVE TOL,275 IDC, |
| 中文描述： | 非隔離DC / DC電源模塊微型貼片足跡- 1.8 - 12V輸入，0.9V至3.6V的輸出 |
| 文件頁數： | 9/23頁 |
| 文件大小： | 684K |
| 代理商： | APC12F08-9J |
Technical Reference Notes
APC12 Centauri II
Enable Pin (Standard configuration)
Pin P5 is functioned to enable the output voltage of a
module. If this pin is left open or connected to
≥
4.1Vdc
up to 14Vdc, the module is turned on. On the other hand,
if this pin is connected to ground or to a voltage potential
from 0 to 0.8Vdc, the module is turned off. The enable pin
can source current up to 60
μ
A max - suited for typical
open-collector transistors readily available in the market.
For TTL compatibility, Figure 3 shows a 7405 open
collector inverter IC utilized to function the Enable
feature. Other common chips that can do the function are
74S05; 74HCT05; non-inverting - 7407; 74S07; 74HC07.
If SMT packaging is preferred, Fairchild's Tiny Logic
NC7SZ05 or TI's Little Logic SN7SLVC1G06 comes in SOT23
or SC70 packages.
Special Feature Pins (Options):
Trim Function (-9):
Pin P4 is used for output voltage adjustment. The output voltage can be trimmed through an external resistor or through an
external DC supply as described in the succeeding sections.
Method 1: External Trim Resistor
.
By connecting an external resistor across P4 and P3 (Gnd), the voltage appearing on pin P2 (Vo) is adjusted to a higher value.
The output voltage of a module can be adjusted up to a maximum value of 3.3V (nominal) or 83% of the input voltage,
whichever is lower. By connecting an external resistor across P4 and P2, Vo is adjusted to a lower value. Only small
reductions, 2%, in voltage are recommended, as adjustment to lower voltages tends to affect the loop compensation of the
module.
Full range adjustment (from 0.9V to 3.6V) can be obtained from a module with the lowest Vo setpoint (0.9Vo).
MODEL: APC12 SERIES
JANUARY 6, 2002 REVISION A (PRELIMINARY)
SHEET 9 OF 23
Figure 3. Output Voltage Enable function diagram.
相關PDF資料 |
PDF描述 |
|---|---|
| APC12F08-9MAJ | CHOKE,AXIAL,CONFORMAL,1000uH, 5% INDUCTIVE TOL,100 IDC, |
| APC12G03-9J | CHOKE,AXIAL,CONFORMAL,27uH, 10% INDUCTIVE TOL,390 IDC, |
| APC12G03-9MAJ | CHOKE,AXIAL,CONFORMAL,33uH, 5% INDUCTIVE TOL,370 IDC, |
| APC12G08-9J | CHOKE,AXIAL,CONFORMAL,390uH, 5% INDUCTIVE TOL,133 IDC, |
| APC12G08-9MAJ | CHOKE,AXIAL,CONFORMAL,47uH, 5% INDUCTIVE TOL,340 IDC, |
相關代理商/技術參數 |
參數描述 |
|---|---|
| APC12F08-9MAJ | 制造商:ASTEC 制造商全稱:Astec America, Inc 功能描述:Non-Isolated DC/DC Power Module Tiny SMT Footprint - 1.8V-12V Input, 0.9V to 3.6V Output |
| APC12F08-9MAL | 功能描述:DC/DC轉換器 DC-DC 1-OUT 3.3V 12A 7-Pin SMT RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| APC12F08-JL | 功能描述:DC/DC轉換器 DC-DC 1-OUT 3.3V 12A 7-Pin SMT RoHS:否 制造商:Murata 產品: 輸出功率: 輸入電壓范圍:3.6 V to 5.5 V 輸入電壓（標稱）: 輸出端數量:1 輸出電壓（通道 1）:3.3 V 輸出電流（通道 1）:600 mA 輸出電壓（通道 2）: 輸出電流（通道 2）: 安裝風格:SMD/SMT 封裝 / 箱體尺寸: |
| APC12G03 | 制造商:ASTEC 制造商全稱:Astec America, Inc 功能描述:Non-Isolated DC/DC Power Module Tiny SMT Footprint - 1.8V-12V Input, 0.9V to 3.6V Output |
| APC12G03-9J | 制造商:ASTEC 制造商全稱:Astec America, Inc 功能描述:Non-Isolated DC/DC Power Module Tiny SMT Footprint - 1.8V-12V Input, 0.9V to 3.6V Output |
發布緊急采購，3分鐘左右您將得到回復。