- 您現在的位置：買賣IC網 > PDF目錄9719 > AR1020T-I/ML (Microchip Technology)IC TOUCH SCREEN CTRLR 20-QFN PDF資料下載
參數資料
| 型號： | AR1020T-I/ML |
| 廠商： | Microchip Technology |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TOUCH SCREEN CTRLR 20-QFN |
| 標準包裝： | 3,300 |
| 類型： | 電阻 |
| 觸摸面板接口： | 4 線，5 線，8 線 |
| 輸入數/鍵： | 3 鍵 |
| 分辨率（位）： | 10 b |
| 數據接口： | I²C，串行，SPI? |
| 電源電壓： | 3.3 V ~ 5.5 V |
| 電流 - 電源： | 17mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 20-QFN 裸露焊盤（4x4） |
| 包裝： | 帶卷 (TR) |
2009-2012 Microchip Technology Inc.
Preliminary
DS41393B-page 7
AR1000 SERIES RESISTIVE TOUCH SCREEN CONTROLLER
2.0
BASICS OF RESISTIVE
SENSORS
2.1
Terminology
ITO (Indium Tin Oxide) is the resistive coating that
makes up the active area of the touch sensor. ITO is a
transparent semiconductor that is sputtered onto the
touch sensor layers.
Flex or Film or Topsheet is the top sensor layer that a
user touches. Flex refers to the fact that the top layer
physically flexes from the pressure of a touch.
Stable or Glass is the bottom sensor layer that
interfaces against the display.
Spacer Adhesive is a frame of adhesive that connects
the flex and stable layers together around the perimeter
of the sensor.
Spacer
Dots
maintain
physical
and
electrical
separation between the flex and stable layers. The dots
are typically printed onto the stable layer.
Bus Bars or Silver Frit electrically connect the ITO on
the flex and stable layers to the sensor’s interface tail.
Bus bars are typically screen printed silver ink. They
are typically much lower in resistivity than the ITO.
X-Axis is the left and right direction on the touch sensor.
Y-Axis is the top and bottom direction on the touch
sensor.
Drive Lines supply a voltage gradient across the
sensor.
2.2
General
Resistive 4, 5, and 8-wire touch sensors consist of two
facing conductive layers, held in physical separation
from each other. The force of a touch causes the top
layer to deflect and make electrical contact with the
bottom layer.
Touch position measurements are made by applying a
voltage gradient across a layer or axis of the touch
sensor. The touch position voltage for the axis can be
measured using the opposing layer.
A comparison of typical sensor constructions is shown
below in Table 2-1.
The
AR1000
Series
Resistive
Touch
Screen
Controllers will work with any manufacturers of analog
resistive 4, 5 and 8-wire touch screens. The
communications and decoding are included, allowing
the user the quickest simplest method of interfacing
analog resistive touch screens into their applications.
The
AR1000
Series
was
designed
with
an
understanding of the materials and processes that
make up resistive touch screens. The AR1000 Series
Touch Controller is not only reliable, but can enhance
the reliability and longevity of the resistive touch
screen, due to its advanced filtering algorithms and
wide range of operation.
TABLE 2-1:
SENSOR COMPARISON
Sensor
Comments
4-Wire
Less expensive than 5-wire or 8-wire
Lower power than 5-wire
More linear (without correction) than 5-wire
Touch inaccuracies occur from flex layer damage or resistance changes
5-Wire
Maintains touch accuracy with flex layer damage
Inherent nonlinearity often requires touch data correction
Touch inaccuracies occur from resistance changes
8-Wire
More expensive than 4-wire
Lower power than 5-wire
More linear (without correction) than 5-wire
Touch inaccuracies occur from flex layer damaged
Maintains touch accuracy with resistance changes
相關PDF資料 |
PDF描述 |
|---|---|
| VI-202-MX-F2 | CONVERTER MOD DC/DC 15V 75W |
| AR1010-I/SO | IC TOUCH SCREEN CTRLR 20-SOIC |
| AR1010T-I/SS | IC TOUCH SCREEN CTRLR 20-SSOP |
| AR1020T-I/SS | IC TOUCH SCREEN CTRLR 20-SSOP |
| VE-B4K-IV-B1 | CONVERTER MOD DC/DC 40V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AR1021-I/ML | 功能描述:觸摸屏轉換器和控制器 Touch Sensing Cont RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| AR1021-I/SO | 功能描述:觸摸屏轉換器和控制器 Touch Sensing Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| AR1021-I/SS | 功能描述:觸摸屏轉換器和控制器 Touch Sensing Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| AR1021T-I/ML | 功能描述:觸摸屏轉換器和控制器 Touch Sensing Cont RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
| AR1021T-I/SO | 功能描述:觸摸屏轉換器和控制器 Touch Sensing Controller RoHS:否 制造商:Microchip Technology 類型:Resistive Touch Controllers 輸入類型:3 Key 數據速率:140 SPS 分辨率:10 bit 接口類型:4-Wire, 5-Wire, 8-Wire, I2C, SPI 電源電壓:2.5 V to 5.25 V 電源電流:17 mA 工作溫度:- 40 C to + 85 C 封裝 / 箱體:SSOP-20 |
發布緊急采購，3分鐘左右您將得到回復。