- 您現在的位置：買賣IC網 > PDF目錄379672 > ARD5004HQ (Electronic Theatre Controls, Inc.) 26.5GHz, 18GHz COAXIAL SWITCH PDF資料下載
參數資料
| 型號： | ARD5004HQ |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 26.5GHz, 18GHz COAXIAL SWITCH |
| 中文描述： | 26.5GHz的，18GHz同軸開關 |
| 文件頁數： | 8/8頁 |
| 文件大小： | 541K |
| 代理商： | ARD5004HQ |
RD
NOTES
1. Coil operating power
Pure DC current should be applied to the
coil. The wave form should be rectangular.
If it includes ripple, the ripple factor should
be less than 5%.
However, check it with the actual circuit
since the characteristics may be slightly
different. The nominal operating voltage
should be applied to the coil for more than
50 ms to set/reset the latching type relay.
Please use the latching type for circuits
that are continually powered for long
periods of time.
2. Coil connection
When connecting coils, refer to the wiring
diagram to prevent mis-operation or
malfunction.
3. Connection of coil indicator and
washing conditions
1) The connection of coil indicator
terminal shall be done by soldering.
Soldering conditions
Max. 260°C
500°F
(solder temp) within
10sec (soldering time)
Max. 350°C
662°F
(solder temp) within
3sec (soldering time)
2) This product is not sealed type,
therefore washing is not allowed.
4. Usage, transport and storage
conditions
1) Ambient temperature, humidity, and
atmospheric pressure during usage,
transport, and storage of the relay:
(1) Temperature:
–55 to +85°C
–67 to +185°F
(2) Humidity: 5 to 85% RH
(Avoid freezing and condensation.)
The humidity range varies with the
temperature. Use within the range
indicated in the graph below.
200303
(3) Atmospheric pressure: 86 to 106 kPa
Temperature and humidity range for
usage, transport, and storage:
2) Condensation
Condensation forms when there is a
sudden change in temperature under high
temperature and high humidity conditions.
Condensation will cause deterioration of
the relay insulation.
3) Freezing
Condensation or other moisture may
freeze on the relay when the temperature
is lower than 0°C
32°F
. This causes
problems such as sticking of movable
parts or operational time lags.
4) Low temperature, low humidity
environments.
The plastic becomes brittle if the relay is
exposed to a low temperature, low
humidity environment for long periods of
time.
5) Low-temperature and low-humidity
atmosphere.
When exposed to low temperature and
low humidity for a long time, the relay’s
plastic casing may become breakable.
5. Other handling precautions.
1) The relay’s on/off service life is based
on standard test conditions (temperature:
15 to 35°C
59 to 95°F
, humidity: 25 to
75%) specified in JIS C5442-1996. Life
will depend on many factors of your
system: coil drive circuit, type of load,
switching intervals, switching phase,
ambient conditions, to name a few.
2) Use the relay within specifications such
as coil rating, contact rating and on/off
service life. If used beyond limits, the relay
may overheat, generate smoke or catch
fire.
3) Be careful not to drop the relay. If
accidentally dropped, carefully check its
appearance and characteristics before
use.
4) Be careful to wire the relay correctly.
Otherwise, malfunction, overheat, fire or
other trouble may occur.
5) The latching type relay is shipped in the
reset position. But jolts during transport or
impacts during installation can move it to
the set position. It is, therefore, advisable
to build a circuit in
which the relay can be initialized (set and
reset) just after turning on the power.
6) If a relay stays on in a circuit for many
months or years at a time without being
activated, circuit design should be
reviewed so that the relay can remain
non-excited. A coil that receives current
all the time heats, which degrades
insulation earlier than expected. A
latching type relay is recommended for
such circuits.
7) For SMA connectors, we recommend a
torque of 0.90±0.1 N·m for installation,
which falls within the prescribed torque of
MIL-C-39012. Please be aware that
conditions might be different depending
on the connector materials and how it
interacts with surrounding materials.
8) Please do not use silicon based
substances such as silicon rubber, silicon
oil, silicon coatings and silicon fillings, in
the vicinity of the relay. Doing so may
cause volatile silicon gas to form which
may lead to contact failure due to the
adherence of silicon on the contacts when
they open and close in this atmosphere.
Tolerance range
(Avoid
condensation when
used at temperatures
higher than 0
°
C
32
°
F
)
(Avoid freezing when
used at temperatures
lower than 0
°
C
32
°
F
)
5
85
Temperature,
°
C
°
F
Humidity, %RH
–55
–67
0
+32
+85
+185
Please contact ..........
Specifications are subject to change without notice.
Printed in Japan.
Automation Controls Company
K
Head Office: 1048, Kadoma, Kadoma-shi, Osaka 571-8686, Japan
K
Telephone: Japan (81) Osaka (06) 6908-1050
K
Facsimile: Japan (81) Osaka (06) 6908-5781
http://www.nais-e.com/
COPYRIGHT 2003 All Rights Reserved
Matsushita Electric Works, Ltd.
These materials are printed on ECF pulp.
These materials are printed with earth-friendly vegetable-based (soybean oil) ink.
相關PDF資料 |
PDF描述 |
|---|---|
| ARD5204H | 26.5GHz, 18GHz COAXIAL SWITCH |
| ARD5204HC | 26.5GHz, 18GHz COAXIAL SWITCH |
| ARD5204HCQ | 26.5GHz, 18GHz COAXIAL SWITCH |
| ARD5204HQ | 26.5GHz, 18GHz COAXIAL SWITCH |
| ARD55105 | 26.5GHz, 18GHz COAXIAL SWITCH |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ARD52012 | 功能描述:同軸開關 SWITCH COAX LATCH SP 26.5GHZ 12V RoHS:否 制造商:Teledyne Relays 觸點形式:SPDT 頻率:18 GHz 線圈電壓:12 VDC 端接類型:SMA VSWR:1.5 介入損耗:0.5 dB 絕緣:60 dB |
| ARD52012C | 制造商:NAIS 制造商全稱:Nais(Matsushita Electric Works) 功能描述:26.5GHz, 18GHz COAXIAL SWITCH |
| ARD52012CQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:26.5GHz, 18GHz COAXIAL SWITCH |
| ARD52012J | 制造商:Panasonic Electric Works 功能描述: |
| ARD52012Q | 功能描述:同軸開關 SWITCH COAX LATCH SP 26.5GHZ 12V RoHS:否 制造商:Teledyne Relays 觸點形式:SPDT 頻率:18 GHz 線圈電壓:12 VDC 端接類型:SMA VSWR:1.5 介入損耗:0.5 dB 絕緣:60 dB |
發布緊急采購，3分鐘左右您將得到回復。