參數資料
型號: ASM706PCSAF-T
元件分類: 電源管理
英文描述: 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
封裝: ROHS COMPLIANT, SOP-8
文件頁數: 14/18頁
文件大小: 305K
代理商: ASM706PCSAF-T
5 of 18
Notice: The information in this document is subject to change without notice
3/3.3/4.0 V P Supervisor Circuits
ASM706 P/ R/ S/ T/ J
ASM708 R/ S/ T/ J
April 2005
rev 1.5
Detailed Descriptions
A
proper
reset
input
enables
a
microprocessor/
microcontroller to start in a known state. ASM706 P/ R/ S/ T/
J and ASM708 R/ S/ T/ J assert reset to prevent code
execution errors during power-up, power-down and brown-
out conditions.
RESET/RESET Operation
The RESET/RESET signals are designed to start or return a
P/C to a known state.
With VCC above 1.2V, RESET and RESET are guaranteed to
be asserted. During a power-up sequence, the reset outputs
remain asserted until the supply rises above the threshold
level. The resets are deasserted approximately 200ms after
crossing the threshold.
In a brownout situation where VCC falls below the threshold
level, the reset outputs are asserted. If a brownout occurs
during an already initiated reset period, the reset period will
extend for an additional reset period of 200ms.
The ASM708 devices have dual reset outputs, one active
LOW and one active HIGH. The ASM706P has a single
active HIGH reset and the ASM706/R/S/T/J devices have an
active LOW reset output.
Manual Reset (MR)
The active-LOW manual reset input is pulled high by an
internal 20k
pull-up resistor and can be driven low by
CMOS/TTL logic or a mechanical switch to ground. An
external debounce circuit is unnecessary since the 140ms
minimum reset time will debounce mechanical push button
switches. The minimum MR input pulse width is 0.5
s with a
3V VCC input and 0.15s with a 5V VCC input. If not used, tie
MR to VCC or leave floating.
By connecting the watchdog output (WDO) and MR, a
watchdog timeout forces a RESET to be generated.
Watchdog Timer
A watchdog timer available on the ASM706P/R/S/T/J
monitors
P/C activity. An output line on the processor is
used to toggle the WDI line. If the line is not toggled within 1.6
seconds on the Watchdog Input (WDI), the internal timer puts
the Watchdog Output (WDO) into a LOW state. WDO will
remain LOW until a toggle is detected at WDI.
The watchdog function is disabled, meaning it is cleared and
not counting, if WDI is floated or connected to a three-stated
circuit. The watchdog timer is also disabled if RESET is
asserted. When RESET becomes inactive and the WDI input
sees a high or low transition as short as 100ns (VCC = 2.7V)/
50ns (VCC = 4.5V), the watchdog timer will begin a 1.6
Alliance
Part #
RESET
Polarity
Threshold
Watchdog
Timer
ASM706P
HIGH
2.63V
YES
ASM706R
LOW
2.63V
YES
ASM706S
LOW
2.93V
YES
ASM706T
LOW
3.08V
YES
ASM706J
LOW
4.00V
YES
ASM708R
HIGH & LOW
2.63V
NO
ASM708S
HIGH & LOW
2.93V
NO
ASM708T
HIGH & LOW
3.08V
NO
ASM708J
HIGH & LOW
4.00V
NO
Figure 1: WDI Three-state operation
相關PDF資料
PDF描述
ASM706SCUAF-T 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
ASM706SEPAF 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8
ASM706JCUA-T 2-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8
ASM809JEURF-T 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3
ASM8I18S42ERG-08-SX 1 A SWITCHING CONTROLLER, 400 kHz SWITCHING FREQ-MAX, PDSO8
相關代理商/技術參數
參數描述
ASM706PCUA 制造商:ALSC 制造商全稱:Alliance Semiconductor Corporation 功能描述:3/3.3/4.0 V uP Supervisor Circuits
ASM706PEPA 制造商:ALSC 制造商全稱:Alliance Semiconductor Corporation 功能描述:3/3.3/4.0 V uP Supervisor Circuits
ASM706PESA 制造商:ALSC 制造商全稱:Alliance Semiconductor Corporation 功能描述:3/3.3/4.0 V uP Supervisor Circuits
ASM706RCPA 制造商:ALSC 制造商全稱:Alliance Semiconductor Corporation 功能描述:3/3.3/4.0 V uP Supervisor Circuits
ASM706RCSA 制造商:ALSC 制造商全稱:Alliance Semiconductor Corporation 功能描述:3/3.3/4.0 V uP Supervisor Circuits