THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
PRODUCT
DA T A
SHEET
Specifications subject to change without notice.
DATASHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
The Connor-Winfield
ASOV5S3 is a true Surface
Mount 5.0V Oven Controlled
Crystal Oscillator (OCXO) with
an HCMOS output. The
ASOV5S3 is designed for
Stratum 3 applications
requiring tight frequency
stability and low jitter.
1
2
ASOV5S3 - 12.80MHz
OCXO
SERIES
CENTER
FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
FREQUENCY ADJUST
5.0V OPERATION
LOW JITTER <1pS RMS
TEMPERATURE STABILITY
±0.25ppm
FREQUENCY TOLERANCE OF
±4.6ppm OVER TWENTY YEARS
SURFACE MOUNT PACKAGE
TAPE AND REEL PACKAGING
SURFACE MOUNT 5.0V HCMOS STRATUM 3 OCXO
ASOV5S3
Cx016
04
6/24/03
www.conwin.com
C
W
0
1
0
7
A
S
O
V
5
S
3
1
2
.8
0
M
ABSOLUTE MAXIMUM RATINGS
TABLE 1.0
PARAMETER
UNITS
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
Storage Temperature
-40
-
85
°C
Supply Voltage
(Vcc)
-0.5
-
7.0
Vdc
Control Voltage
(Vc)
-0.5
-
7.0
Vdc
OPERATING SPECIFICATIONS
TABLE 2.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
Center Frequency
(Fo)
1.544
-
20.0
MHz
Frequency Calibration, Vc=2.18 Vdc
-1.5
1.5
ppm
1
Frequency Stability
-0.25
-
0.25
ppm
2
Aging (Daily)
-30
-
30
ppb
3
Aging (20 Years)
-2.5
-
2.5
ppm
Total Frequency Tolerance
-4.6
-
4.6
ppm
4
Operating Temperature Range
0
-
70
°C
Supply Voltage
(Vcc)
4.75
5.0
5.25
Vdc
Supply Current
(Icc)
-
350
mA
Phase Jitter (BW=12KHz to 20MHz)
-
1
ps rms
Phase Jitter (BW=10Hz to 20MHz)
-
3
ps rms
Period Jitter
-
3
ps rms
SSB Phase Noise at 10Hz offset
-
-90
-
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-135
-
dBc/Hz
Start Up Time: Oscillator
-
10
mS
Warm Up Time
-
5
Minutes
5
TDEV @ 1.0 Sec.
-
1
nS
TDEV @ 4.0 Sec.
-
2
nS
INTPUT CHARACTERISTICS
TABLE 3.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
Control Voltage Range
(Vc)
0.5
2.18
4.1
Vdc
Frequency at Vc=0.3 Vdc
-30
-
-18
ppm
6
Frequency at Vc=3.0 Vdc
18
-
30
ppm
6
Slope of Frequency Adjust
5
-
ppm/V
Input Impedance
100k
-
Ohm
HCMOS OUTPUT CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
LOAD
-
15
pf
Voltage
(High)
(Voh)
4.5
-
Vdc
(Low)
(Vol)
-
0.4
Vdc
Current
(High)
(Ioh)
-4
-
mA
(Low)
(Ioh)
-
4
mA
Duty Cycle at 50% of Vcc
45
50
55
%
Rise / Fall Time 10% to 90%
-
6
nS
PACKAGE CHARACTERISTICS
TABLE 5.0
Package
Surface Mount, Non-hermetic package consisting of an FR4 substrate with
grounded metal cover.
PROCESS RECOMMENDATIONS
TABLE 6.0
Solder Reflow
The component solder used internal to this device has a mel ting point of
221
°C. The peak temperature inside the device should be less than or equal
to 220
°C for a maximum of 10 seconds
Wash
Ultrasonic cleaning is not recommended
Notes:
1) Initial calibration @ 25
°C, Vc=2.18 Vdc.
2) Frequency vs. temperature stability
3) At the time of shipment after48 hours of operation.
4) Inclusive of calibration, operating temperature range, supply voltage change, load change, shock
and vibration, 20 years aging, Vc=2.18 Vdc.
°C, within 5 minutes, the unit will be within +/-0.1ppm of its reference frequency,
measured after 30 minutes of continuous operation at a stable 25
°C
6) Referenced to Fo @ 25°C, Positive Transfer Characteristic