- 您現在的位置：買賣IC網 > PDF目錄295111 > AT25080A-10PI-2.7 (ATMEL CORP) SPI Serial EEPROMs PDF資料下載
參數資料
| 型號： | AT25080A-10PI-2.7 |
| 廠商： | ATMEL CORP |
| 元件分類： | PROM |
| 英文描述： | SPI Serial EEPROMs |
| 中文描述： | 1K X 8 SPI BUS SERIAL EEPROM, PDIP8 |
| 封裝： | 0.300 INCH, PLASTIC, MS-001BA, DIP-8 |
| 文件頁數： | 2/23頁 |
| 文件大?。?/td> | 451K |
| 代理商： | AT25080A-10PI-2.7 |
10
AT25080A/160A/320A/640A
3347I–SEEPR–1/05
READ SEQUENCE (READ): Reading the AT25080A/160A/320A/640A via the Serial Output
(SO) pin requires the following sequence. After the CS line is pulled low to select a device, the
read op-code is transmitted via the SI line followed by the byte address to be read (A15–A0,
the specified address is then shifted out onto the SO line. If only one byte is to be read, the CS
line should be driven high after the data comes out. The read sequence can be continued
since the byte address is automatically incremented and data will continue to be shifted out.
When the highest address is reached, the address counter will roll over to the lowest address
allowing the entire memory to be read in one continuous read cycle.
WRITE SEQUENCE (WRITE): In order to program the AT25080A/160A/320A/640A, two sep-
arate instructions must be executed. First, the device
must be write enabled via the WREN
instruction. Then a write (WRITE) instruction may be executed. Also, the address of the mem-
ory location(s) to be programmed must be outside the protected address field location
selected by the block write protection level. During an internal write cycle, all commands will
be ignored except the RDSR instruction.
A write instruction requires the following sequence. After the CS line is pulled low to select the
device, the WRITE op-code is transmitted via the SI line followed by the byte address (A15–
CS pin is brought high. The low-to-high transition of the CS pin must occur during the SCK
low-time immediately after clocking in the D0 (LSB) data bit.
The READY/BUSY status of the device can be determined by initiating a read status register
(RDSR) instruction. If Bit 0 = “1”, the write cycle is still in progress. If Bit 0 = “0”, the write cycle
has ended. Only the RDSR instruction is enabled during the write programming cycle.
The AT25080A/160A/320A/640A is capable of a 32-byte page write operation. After each byte
of data is received, the five low-order address bits are internally incremented by one; the high-
order bits of the address will remain constant. If more than 32 bytes of data are transmitted,
the address counter will roll over and the previously written data will be overwritten. The
AT25080A/160A/320A/640A is automatically returned to the write disable state at the comple-
tion of a write cycle.
NOTE: If the device is not write-enabled (WREN), the device will ignore the write instruction
and will return to the standby state, when CS is brought high. A new CS falling edge is
required to reinitiate the serial communication.
Table 10. Address Key
Address
AT25080A
AT25160A
AT25320A
AT25640A
AN
A 9–A 0
A 10–A 0
A 11–A 0
A 12–A 0
Don’t Care Bits
A 15–A 10
A 15–A 11
A 15–A 12
A 15–A 13
相關PDF資料 |
PDF描述 |
|---|---|
| AT25080A-10TI-1.8 | SPI Serial EEPROMs |
| AT25080A-10TI-2.7 | SPI Serial EEPROMs |
| AT25080A-10TU-2.7 | SPI Serial EEPROMs |
| AT27C080-10PC | 8-Megabit 1M x 8 UV Erasable CMOS EPROM |
| AT27C080-10PI | 8-Megabit 1M x 8 UV Erasable CMOS EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT25080A-10PQ-2.7 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:SPI Serial EEPROMs |
| AT25080A-10PU-1.8 | 功能描述:電可擦除可編程只讀存儲器 1.8V 27 MIL - 10MS 1.8V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT25080A-10PU-2.7 | 功能描述:電可擦除可編程只讀存儲器 1.8V 27 MIL - 10MS 2.7V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| AT25080A-10TI-1.8 | 功能描述:IC EEPROM 8KBIT 20MHZ 8TSSOP RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT25080A-10TI-2.7 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:SPI Serial EEPROMs |
發布緊急采購，3分鐘左右您將得到回復。