- 您現在的位置：買賣IC網 > PDF目錄295111 > AT25080A-10TU-2.7 (ATMEL CORP) SPI Serial EEPROMs PDF資料下載
參數資料
| 型號： | AT25080A-10TU-2.7 |
| 廠商： | ATMEL CORP |
| 元件分類： | PROM |
| 英文描述： | SPI Serial EEPROMs |
| 中文描述： | 1K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 4.40 MM, GREEN, PLASTIC, MO-153AA, TSSOP-8 |
| 文件頁數： | 3/26頁 |
| 文件大?。?/td> | 801K |
| 代理商： | AT25080A-10TU-2.7 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
11
3347L–SEEPR–06/07
AT25080A/160A/320A/640A
READ SEQUENCE (READ): Reading the AT25080A/160A/320A/640A via the Serial Output
(SO) pin requires the following sequence. After the CS line is pulled low to select a device, the
read op-code is transmitted via the SI line followed by the byte address to be read (A15–A0, see
specified address is then shifted out onto the SO line. If only one byte is to be read, the CS line
should be driven high after the data comes out. The read sequence can be continued since the
byte address is automatically incremented and data will continue to be shifted out. When the
highest address is reached, the address counter will roll over to the lowest address allowing the
entire memory to be read in one continuous read cycle.
WRITE SEQUENCE (WRITE): In order to program the AT25080A/160A/320A/640A, two sepa-
rate instructions must be executed. First, the device must be write enabled via the WREN
instruction. Then a write (WRITE) instruction may be executed. Also, the address of the memory
location(s) to be programmed must be outside the protected address field location selected by
the block write protection level. During an internal write cycle, all commands will be ignored
except the RDSR instruction.
A write instruction requires the following sequence. After the CS line is pulled low to select the
device, the WRITE op-code is transmitted via the SI line followed by the byte address (A15–A0)
is brought high. The low-to-high transition of the CS pin must occur during the SCK low-time
immediately after clocking in the D0 (LSB) data bit.
The READY/BUSY status of the device can be determined by initiating a read status register
(RDSR) instruction. If Bit 0 = “1”, the write cycle is still in progress. If Bit 0 = “0”, the write cycle
has ended. Only the RDSR instruction is enabled during the write programming cycle.
The AT25080A/160A/320A/640A is capable of a 32-byte page write operation. After each byte of
data is received, the five low-order address bits are internally incremented by one; the high-
order bits of the address will remain constant. If more than 32 bytes of data are transmitted, the
address counter will roll over and the previously written data will be overwritten. The
AT25080A/160A/320A/640A is automatically returned to the write disable state at the comple-
tion of a write cycle.
NOTE: If the device is not write-enabled (WREN), the device will ignore the write instruction and
will return to the standby state, when CS is brought high. A new CS falling edge is required to
reinitiate the serial communication.
Table 3-5.
WPEN Operation
WPEN
WP
WEN
Protected
Blocks
Unprotected
Blocks
Status
Register
0
X
0
Protected
0
X
1
Protected
Writeable
1
Low
0
Protected
1
Low
1
Protected
Writeable
Protected
X
High
0
Protected
X
High
1
Protected
Writeable
相關PDF資料 |
PDF描述 |
|---|---|
| AT27C080-10PC | 8-Megabit 1M x 8 UV Erasable CMOS EPROM |
| AT27C080-10PI | 8-Megabit 1M x 8 UV Erasable CMOS EPROM |
| AT27HC256R-12JIT/R | 32K X 8 OTPROM, 120 ns, PQCC32 |
| AT3020QR425Z1S-W3 | SINGLE COLOR LED, WARM WHITE, 2.48 mm |
| AT3020QR425Z1S-N1 | SINGLE COLOR LED, NEUTRAL WHITE, 2.48 mm |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT25080AN-10SE-2.7 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:SPI Serial EEPROMs |
| AT25080AN-10SI-1.8 | 功能描述:IC EEPROM 8KBIT 20MHZ 8SOIC RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT25080AN-10SI-1.8 SL383 | 功能描述:IC EEPROM 8KBIT 20MHZ 8SOIC RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
| AT25080AN-10SI-1.8-T | 功能描述:IC EEPROM 8KBIT 20MHZ 8SOIC 制造商:microchip technology 系列:- 包裝:帶卷（TR） 零件狀態:停產 存儲器類型:非易失 存儲器格式:EEPROM 技術:EEPROM 存儲容量:8Kb （1K x 8） 時鐘頻率:20MHz 寫周期時間 - 字，頁:5ms 存儲器接口:SPI 電壓 - 電源:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 85°C（TA） 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商器件封裝:8-SOIC 基本零件編號:AT25080 標準包裝:3,000 |
| AT25080AN-10SI-2.7 | 功能描述:IC EEPROM 8KBIT 20MHZ 8SOIC RoHS:否 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:96 系列:- 格式 - 存儲器:閃存 存儲器類型:FLASH 存儲容量:16M（2M x 8，1M x 16） 速度:70ns 接口:并聯 電源電壓:2.65 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP（0.724"，18.40mm 寬） 供應商設備封裝:48-TSOP 包裝:托盤 |
發布緊急采購，3分鐘左右您將得到回復。