- 您現在的位置：買賣IC網 > PDF目錄362501 > AT77C101B-CB02C Signal Conditioner PDF資料下載
參數資料
| 型號： | AT77C101B-CB02C |
| 英文描述： | Signal Conditioner |
| 中文描述： | 信號調理 |
| 文件頁數： | 18/23頁 |
| 文件大?。?/td> | 415K |
| 代理商： | AT77C101B-CB02C |
18
AT77C101B
2150A
–
BIOM
–
02/02
Power Management
Nap Mode
Several strategies are possible to reduce power consumption when not in use.
The simplest and most efficient is to cut the power supply, using external means.
A nap mode is also implemented in the AT77C101B. To activate this nap mode, the user
must:
1.
Set the reset RST pin to high. Doing this, all analog sections of the device are
internally powered down.
2.
Set the clock PCLK pin to high (or low), thus stopping the entire digital section.
3.
Set the TPE pin to low or disconnect TPP to stop the temperature stabilization
feature.
4.
Set Output Enable OE pin to high, so that output are forced in HiZ.
Figure 14.
Nap Mode
In Nap Mode, all internal transistors are in shut mode. Only leakage current is drained in
power supply, generally less than the tested value.
Static Current
Consumption
When the clock is stopped (set to 1) and the reset is low (set to 0), the analog sections
of the device drain some current and the digital section does not consume current if the
outputs are connected to a standard CMOS input (= no current is drained in the I/O). In
this case the typical current value is 5 mA. This current does not depend on the voltage
(i.e. it is almost the same from 3V to 5.5V).
Dynamic Current
Consumption
When the clock is running, the digital sections are consuming current, and particularly
the outputs if they are heavily loaded. In any case, it should be less than the testing
machine (120 pF load on each I/O), 50 pF maximum is recommended.
Connected to a USB interface chip (see application note 26 related to the FCDEMO4
kit) at 5V, and running at about 1 MHz, the AT77C101B consumes less than 7 mA on
V
CC
pin.
Temperature
Stabilization Power
Consumption (TPP pin)
When the TPE pin is set to 1, current is drained via the TPP pin. The current is limited by
the internal equivalent resistance given in table 4 and a possible external resistor.
Most of the time, TPE is set to 0 and no current is drained in TPP. When the image con-
trast becomes low because of a low temperature differential (less than one Kelvin), then
it is recommended to set TPE to 1 during a short time so that the dissipated power in the
chip elevates the temperature, enabling to recover contrast. The necessary time to
increase the chip temperature of one Kelvin depends on the dissipated power, the ther-
mal capacity of the silicon sensor and the thermal resistance between the sensor and
the surroundings.
As a rule of thumb, dissipating 300 mW in the chip elevates the temperature of 1 Kelvin
in one second. With the 30
typical value, 300 mW is 3V applied on TPP.
Nap
Clock PCLK
Reset RST
Nap mode
相關PDF資料 |
PDF描述 |
|---|---|
| AT77C101B-CB01C | Signal Conditioner |
| AT78C1501 | AT78C1501 [Updated 7/02. 15 Pages] DVD Interface Controller supporting all current DVD and CD writeable and rewriteable standards. |
| AT78C1501-208TC | Controller Miscellaneous - Datasheet Reference |
| AT78C1504 | Controller Miscellaneous - Datasheet Reference |
| AT80C51ID2 | AT83C51RB2. AT83C51RC2. AT83C51IC2. AT80C51ID2 Errata [Updated 7/03. 4 Pages] |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT77C102B | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Thermal Fingerprint Sensor with 0.4 mm x 14 mm (0.02 x 0.55) Sensing Area and Digital Output (On-chip ADC) |
| AT77C102B_07 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Thermal Fingerprint Sensor with 0.4 mm x 14 mm (0.02" x 0.55") Sensing Area and Digital Output (On-chip ADC) |
| AT77C102B-CB01YV | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Thermal Fingerprint Sensor with 0.4 mm x 14 mm (0.02" x 0.55") Sensing Area and Digital Output (On-chip ADC) |
| AT77C102B-CB01YV- | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Thermal Fingerprint Sensor with 0.4 mm x 14 mm (0.02 x 0.55) Sensing Area and Digital Output (On-chip ADC) |
| AT77C102B-CB02YV | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Thermal Fingerprint Sensor with 0.4 mm x 14 mm (0.02" x 0.55") Sensing Area and Digital Output (On-chip ADC) |
發布緊急采購，3分鐘左右您將得到回復。