- 您現在的位置：買賣IC網 > PDF目錄3774 > AT80C51RD2-RLRUM (Atmel)IC MCU 80C51 HI PERFORM 44VQFP PDF資料下載
參數資料
| 型號： | AT80C51RD2-RLRUM |
| 廠商： | Atmel |
| 文件頁數： | 52/81頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU 80C51 HI PERFORM 44VQFP |
| 產品培訓模塊： | MCU Product Line Introduction |
| 標準包裝： | 1 |
| 系列： | 80C |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 40MHz |
| 連通性： | UART/USART |
| 外圍設備： | POR，PWM，WDT |
| 輸入/輸出數： | 32 |
| 程序存儲器類型： | ROMless |
| RAM 容量： | 1K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 44-LQFP |
| 包裝： | 標準包裝 |
| 其它名稱： | AT80C51RD2-RLRUMDKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁
56
4113D–8051–01/09
AT80C51RD2
14. Power Management
14.1
Idle Mode
An instruction that sets PCON.0 indicates that it is the last instruction to be executed before
going into Idle mode. In Idle mode, the internal clock signal is gated off to the CPU, but not to the
interrupt, Timer, and Serial Port functions. The CPU status is preserved in its entirety: the Stack
Pointer, Program Counter, Program Status Word, Accumulator and all other registers maintain
their data during idle. The port pins hold the logical states they had at the time Idle was acti-
vated. ALE and PSEN hold at logic high level.
There are two ways to terminate the Idle mode. Activation of any enabled interrupt will cause
PCON.0 to be cleared by hardware, terminating the Idle mode. The interrupt will be serviced,
and following RETI the next instruction to be executed will be the one following the instruction
that put the device into idle.
The flag bits GF0 and GF1 can be used to give an indication if an interrupt occurred during nor-
mal operation or during idle. For example, an instruction that activates idle can also set one or
both flag bits. When idle is terminated by an interrupt, the interrupt service routine can examine
the flag bits.
The other way of terminating the Idle mode is with a hardware reset. Since the clock oscillator is
still running, the hardware reset needs to be held active for only two machine cycles (24 oscilla-
tor periods) to complete the reset.
14.2
Power-down Mode
To save maximum power, a power-down mode can be invoked by software (refer to Table 11-
12, PCON register).
In power-down mode, the oscillator is stopped and the instruction that invoked power-down
mode is the last instruction executed. The internal RAM and SFRs retain their value until the
power-down mode is terminated. V
CC can be lowered to save further power. Either a hardware
reset or an external interrupt can cause an exit from power-down. To properly terminate power-
down, the reset or external interrupt should not be executed before V
CC is restored to its normal
operating level and must be held active long enough for the oscillator to restart and stabilize.
Only external interrupts INT0, INT1 and Keyboard Interrupts are useful to exit from power-down.
Thus, the interrupt must be enabled and configured as level - or edge - sensitive interrupt input.
When Keyboard Interrupt occurs after a power-down mode, 1024 clocks are necessary to exit to
power-down mode and enter in operating mode.
Holding the pin low restarts the oscillator but bringing the pin high completes the exit as detailed
in Figure 14-1. When both interrupts are enabled, the oscillator restarts as soon as one of the
two inputs is held low and power-down exit will be completed when the first input is released. In
this case, the higher priority interrupt service routine is executed. Once the interrupt is serviced,
the next instruction to be executed after RETI will be the one following the instruction that put
AT80C51RD2 into power-down mode.
相關PDF資料 |
PDF描述 |
|---|---|
| 42973-3 | RETAINING SPRING AMP LF L.P. |
| 42973-1 | RETAINING SPRING AMP LF L.P. |
| MAX7320AEE+ | IC I/O EXPANDER I2C 8B 16QSOP |
| PCA9673D,112 | IC I/O EXPANDER I2C 16B 24SOIC |
| 530286-3 | CONN KEYING PLUG TWIN LEAF .040 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT80C51RD2-RLTIL | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:80C51 High Performance ROM 8-bit Microcontroller |
| AT80C51RD2-RLTIM | 功能描述:IC MCU 8051 5V SPI 20MHZ 44-VQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:80C 標準包裝:9 系列:87C 核心處理器:8051 芯體尺寸:8-位 速度:40/20MHz 連通性:UART/USART 外圍設備:POR，WDT 輸入/輸出數:32 程序存儲器容量:32KB（32K x 8） 程序存儲器類型:OTP EEPROM 大小:- RAM 容量:256 x 8 電壓 - 電源 (Vcc/Vdd):4.5 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:0°C ~ 70°C 封裝/外殼:40-DIP（0.600"，15.24mm） 包裝:管件 |
| AT80C51RD2-RLTUL | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:80C51 High Performance ROM 8-bit Microcontroller |
| AT80C51RD2-RLTUM | 功能描述:8位微控制器 -MCU MCU 8-Bit HI Perform ROMless 3-5V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| AT80C51RD2-SLRUM | 功能描述:8位微控制器 -MCU MCU 8-Bit HI Perform ROMless 3-5V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。