- 您現在的位置：買賣IC網 > PDF目錄11217 > AT89C2051-12PU (Atmel)IC 8051 MCU FLASH 2K 20DIP PDF資料下載
參數資料
| 型號： | AT89C2051-12PU |
| 廠商： | Atmel |
| 文件頁數： | 17/19頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 8051 MCU FLASH 2K 20DIP |
| 產品培訓模塊： | MCU Product Line Introduction |
| 標準包裝： | 18 |
| 系列： | 89C |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 12MHz |
| 連通性： | UART/USART |
| 外圍設備： | LED |
| 輸入/輸出數： | 15 |
| 程序存儲器容量： | 2KB（2K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 128 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 6 V |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 20-DIP（0.300"，7.62mm） |
| 包裝： | 管件 |
7
0368H–MICRO–6/08
AT89C2051
9.
Idle Mode
In idle mode, the CPU puts itself to sleep while all the on-chip peripherals remain active. The
mode is invoked by software. The content of the on-chip RAM and all the special functions regis-
ters remain unchanged during this mode. The idle mode can be terminated by any enabled
interrupt or by a hardware reset.
The P1.0 and P1.1 should be set to “0” if no external pull-ups are used, or set to “1” if
external pull-ups are used.
It should be noted that when idle is terminated by a hardware reset, the device normally
resumes program execution, from where it left off, up to two machine cycles before the internal
reset algorithm takes control. On-chip hardware inhibits access to internal RAM in this event, but
access to the port pins is not inhibited. To eliminate the possibility of an unexpected write to a
port pin when Idle is terminated by reset, the instruction following the one that invokes Idle
should not be one that writes to a port pin or to external memory.
10. Power-down Mode
In the power-down mode the oscillator is stopped, and the instruction that invokes power-down
is the last instruction executed. The on-chip RAM and Special Function Registers retain their
values until the power-down mode is terminated. The only exit from power-down is a hardware
reset. Reset redefines the SFRs but does not change the on-chip RAM. The reset should not be
activated before V
CC is restored to its normal operating level and must be held active long
enough to allow the oscillator to restart and stabilize.
The P1.0 and P1.1 should be set to “0” if no external pull-ups are used, or set to “1” if
external pull-ups are used.
11. Programming The Flash
The AT89C2051 is shipped with the 2K bytes of on-chip PEROM code memory array in the
erased state (i.e., contents = FFH) and ready to be programmed. The code memory array is pro-
grammed one byte at a time. Once the array is programmed, to re-program any non-blank byte,
the entire memory array needs to be erased electrically.
Internal Address Counter: The AT89C2051 contains an internal PEROM address counter
which is always reset to 000H on the rising edge of RST and is advanced by applying a positive
going pulse to pin XTAL1.
Programming Algorithm: To program the AT89C2051, the following sequence is
recommended.
1.
Power-up sequence:
Apply power between V
CC and GND pins
Set RST and XTAL1 to GND
2.
Set pin RST to “H”
Set pin P3.2 to “H”
3.
Apply the appropriate combination of “H” or “L” logic
levels to pins P3.3, P3.4, P3.5, P3.7 to select one of the programming operations
shown in the PEROM Programming Modes table.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B2T-IX-F2 | CONVERTER MOD DC/DC 6.5V 75W |
| ATTINY43U-MUR | MCU AVR 4KB FLASH 8MHZ 20QFN |
| VI-J14-IW | CONVERTER MOD DC/DC 48V 100W |
| VE-B2T-IW-F4 | CONVERTER MOD DC/DC 6.5V 100W |
| ATTINY84-20SSUR | MCU AVR 8KB FLASH 10MHZ 14SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT89C2051-12PU SL383 | 制造商:Atmel Corporation 功能描述:8051 MCU, 20 PINS, UART, 2K FL |
| AT89C2051-12SA | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-Bit Microcontroller with 2K Bytes Flash |
| AT89C205112SC | 制造商:ATMEL 功能描述:* |
| AT89C2051-12SC | 功能描述:8位微控制器 -MCU 20 PINS UART 2K - FLASH - 12MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| AT89C2051-12SI | 功能描述:8位微控制器 -MCU 20 PINS UART 2K - FLASH - 12MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。