參數資料
型號: AT89S2051-24PI
廠商: ATMEL CORP
元件分類: 微控制器/微處理器
英文描述: 8-bit Microcontroller with 2K/4K Bytes Flash
中文描述: 8-BIT, FLASH, 24 MHz, MICROCONTROLLER, PDIP20
封裝: 0.300 INCH, MS-001AD, PLASTIC, DIP-20
文件頁數: 9/46頁
文件大?。?/td> 1051K
代理商: AT89S2051-24PI
17
3390D–MICRO–3/07
AT89S2051/S4051
Notes:
1. SMOD is located at PCON.7.
2. f
osc = frequency.
Table 17-1.
SCON – Serial Port Control Register
SCON Address = 98H
Reset Value = 0000 0000B
Bit Addressable
SM0/FE
SM1
SM2
REN
TB8
RB8
TI
RI
Bit
7
65
43
21
0
(SMOD = 0/1)(1)
Symbol
Function
FE
Framing error bit. This bit is set by the receiver when an invalid stop bit is detected. The FE bit is not cleared by valid
frames but should be cleared by software. The SMOD0 bit must be set to enable access to the FE bit. FE will be set
regardless of the state of SMOD.
SM0
Serial Port Mode Bit 0, (SMOD must = 0 to access bit SM0)
SM1
Serial Port Mode Bit 1
SM2
Enables the Automatic Address Recognition feature in modes 2 or 3. If SM2 = 1 then Rl will not be set unless the received
9th data bit (RB8) is 1, indicating an address, and the received byte is a Given or Broadcast Address. In mode 1, if SM2 =
1 then Rl will not be activated unless a valid stop bit was received, and the received byte is a Given or Broadcast Address.
In Mode 0, SM2 should be 0.
REN
Enables serial reception. Set by software to enable reception. Clear by software to disable reception.
TB8
The 9th data bit that will be transmitted in modes 2 and 3. Set or clear by software as desired.
RB8
In modes 2 and 3, the 9th data bit that was received. In mode 1, if SM2 = 0, RB8 is the stop bit that was
received. In mode 0, RB8 is not used.
TI
Transmit interrupt flag. Set by hardware at the end of the 8th bit time in mode 0, or at the beginning of the
stop bit in the other modes, in any serial transmission. Must be cleared by software.
RI
Receive interrupt flag. Set by hardware at the end of the 8th bit time in mode 0, or halfway through the stop
bit time in the other modes, in any serial reception (except see SM2). Must be cleared by software.
SM0
SM1
Mode
Description
Baud Rate(2)
0
shift register
f
osc/12
0
1
8-bit UART
variable
1
0
2
9-bit UART
f
osc/64 or fosc/32
1
3
9-bit UART
variable
相關PDF資料
PDF描述
AT89S2051-24SC 8-bit Microcontroller with 2K/4K Bytes Flash
AT89S2051-24SI 8-bit Microcontroller with 2K/4K Bytes Flash
AT89S2051-24PU 8-bit Microcontroller with 2K/4K Bytes Flash
AT89S2051-24SU 8-bit Microcontroller with 2K/4K Bytes Flash
AT89S2051 8-bit Microcontroller with 2K/4K Bytes Flash
相關代理商/技術參數
參數描述
AT89S2051-24PU 功能描述:8位微控制器 -MCU 2K FLSH 24MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89S2051-24SU 功能描述:8位微控制器 -MCU 2K FLASH 24MHZ SOIC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89S2051W-16PI 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89S2051W-16SI 功能描述:8位微控制器 -MCU Microcontroller RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
AT89S4051-24PU 功能描述:8位微控制器 -MCU 4K FLASH 24MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT