參數資料
型號： AT91SAM7S32-MU-999
廠商： Atmel
文件頁數： 4/50頁
文件大?。?/td> 0K
描述： IC MCU ARM7 32KB FLASH 48-VQFN
標準包裝： 3,500
系列： SAM7S
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 55MHz
連通性： I²C，SPI，SSC，UART/USART
外圍設備： 欠壓檢測/復位，DMA，POR，PWM，WDT
輸入/輸出數： 21
程序存儲器容量： 32KB（32K x 8）
程序存儲器類型： 閃存
RAM 容量： 8K x 8
電壓 - 電源 (Vcc/Vdd)： 1.65 V ~ 1.95 V
數據轉換器： A/D 8x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 48-VFQFN 裸露焊盤
包裝： 帶卷 (TR)
配用： AT91SAM-ICE-ND - EMULATOR FOR AT91 ARM7/ARM9
AT91SAM7S-EK-ND - KIT EVAL FOR ARM AT91SAM7S
12
SAM7S Series [DATASHEET]
6175KS–ATARM–25-Oct-12
5.
Power Considerations
5.1
Power Supplies
The SAM7S Series has six types of power supply pins and integrates a voltage regulator, allowing the device to be
supplied with only one voltage. The six power supply pin types are:
VDDIN pin. It powers the voltage regulator and the ADC; voltage ranges from 3.0V to 3.6V, 3.3V nominal.
VDDOUT pin. It is the output of the 1.8V voltage regulator.
VDDIO pin. It powers the I/O lines and the USB transceivers; dual voltage range is supported. Ranges from 3.0V
to 3.6V, 3.3V nominal or from 1.65V to 1.95V, 1.8V nominal. Note that supplying less than 3.0V to VDDIO prevents
any use of the USB transceivers.
VDDFLASH pin. It powers a part of the Flash and is required for the Flash to operate correctly; voltage ranges
from 3.0V to 3.6V, 3.3V nominal.
VDDCORE pins. They power the logic of the device; voltage ranges from 1.65V to 1.95V, 1.8V typical. It can be
connected to the VDDOUT pin with decoupling capacitor. VDDCORE is required for the device, including its
embedded Flash, to operate correctly.
During startup, core supply voltage (VDDCORE) slope must be superior or equal to 6V/ms.
VDDPLL pin. It powers the oscillator and the PLL. It can be connected directly to the VDDOUT pin.
No separate ground pins are provided for the different power supplies. Only GND pins are provided and should be
connected as shortly as possible to the system ground plane.
In order to decrease current consumption, if the voltage regulator and the ADC are not used, VDDIN, ADVREF, AD4,
AD5, AD6 and AD7 should be connected to GND. In this case VDDOUT should be left unconnected.
5.2
Power Consumption
The SAM7S Series has a static current of less than 60 A on VDDCORE at 25°C, including the RC oscillator, the voltage
regulator and the power-on reset. When the brown-out detector is activated, 20 A static current is added.
The dynamic power consumption on VDDCORE is less than 50 mA at full speed when running out of the Flash. Under
the same conditions, the power consumption on VDDFLASH does not exceed 10 mA.
5.3
Voltage Regulator
The SAM7S Series embeds a voltage regulator that is managed by the System Controller.
In Normal Mode, the voltage regulator consumes less than 100 A static current and draws 100 mA of output current.
The voltage regulator also has a Low-power Mode. In this mode, it consumes less than 25 A static current and draws 1
mA of output current.
Adequate output supply decoupling is mandatory for VDDOUT to reduce ripple and avoid oscillations. The best way to
achieve this is to use two capacitors in parallel: one external 470 pF (or 1 nF) NPO capacitor must be connected between
VDDOUT and GND as close to the chip as possible. One external 2.2 F (or 3.3 F) X7R capacitor must be connected
between VDDOUT and GND.
Adequate input supply decoupling is mandatory for VDDIN in order to improve startup stability and reduce source voltage
drop. The input decoupling capacitor should be placed close to the chip. For example, two capacitors can be used in
parallel: 100 nF NPO and 4.7 F X7R.
5.4
Typical Powering Schematics
The SAM7S Series supports a 3.3V single supply mode. The internal regulator is connected to the 3.3V source and its
output feeds VDDCORE and the VDDPLL. Figure 5-1 shows the power schematics to be used for USB bus-powered
systems.
相關PDF資料
PDF描述
PIC24HJ128GP506A-I/PT IC PIC MCU FLASH 128KB 64-TQFP
AT91SAM7XC256-AU-999 IC MCU ARM7 256KB FLASH 100LQFP
AT91SAM7S64-AU-999 IC MCU ARM7 64KB FLASH 64LQFP
AT91SAM7XC128-AU-999 IC MCU ARM7 128KB FLASH 100LQFP
AT91SAM7S32-AU-999 IC MCU ARM7 32KB FLASH 48LQFP
相關代理商/技術參數
參數描述
AT91SAM7S512 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91 ARM Thumb-based Microcontrollers
AT91SAM7S512-AU 功能描述:ARM微控制器 - MCU LQFP IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
AT91SAM7S512-AU-999 功能描述:ARM微控制器 - MCU Ind. Temp Green RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
AT91SAM7S512B-AU 功能描述:ARM微控制器 - MCU GREEN IND TEMP MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
AT91SAM7S512B-AU-999 功能描述:ARM微控制器 - MCU GREEN IND TEMP MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*