參數資料
型號: AT91SAM7S512-MU-999
廠商: Atmel
文件頁數: 18/50頁
文件大?。?/td> 0K
描述: IC MCU ARM7 512KB FLASH 64-VQFN
標準包裝: 3,500
系列: SAM7S
核心處理器: ARM7
芯體尺寸: 16/32-位
速度: 55MHz
連通性: I²C,SPI,SSC,UART/USART,USB
外圍設備: 欠壓檢測/復位,DMA,POR,PWM,WDT
輸入/輸出數: 32
程序存儲器容量: 512KB(512K x 8)
程序存儲器類型: 閃存
RAM 容量: 64K x 8
電壓 - 電源 (Vcc/Vdd): 1.65 V ~ 1.95 V
數據轉換器: A/D 8x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 64-VFQFN 裸露焊盤
包裝: 帶卷 (TR)
配用: AT91SAM-ICE-ND - EMULATOR FOR AT91 ARM7/ARM9
AT91SAM7S-EK-ND - KIT EVAL FOR ARM AT91SAM7S
25
SAM7S Series [DATASHEET]
6175KS–ATARM–25-Oct-12
8.8.6
Calibration Bits
Eight NVM bits are used to calibrate the brownout detector and the voltage regulator. These bits are factory configured
and cannot be changed by the user. The ERASE pin has no effect on the calibration bits.
8.9
Fast Flash Programming Interface
The Fast Flash Programming Interface allows programming the device through either a serial JTAG interface or through
a multiplexed fully-handshaked parallel port. It allows gang-programming with market-standard industrial programmers.
The FFPI supports read, page program, page erase, full erase, lock, unlock and protect commands.
The Fast Flash Programming Interface is enabled and the Fast Programming Mode is entered when the TST pin and the
PA0 and PA1 pins are all tied high and PA2 is tied low.
8.10 SAM-BA Boot Assistant
The SAM-BA
Boot Recovery restores the SAM-BA Boot in the first two sectors of the on-chip Flash memory. The
SAM-BA Boot recovery is performed when the TST pin and the PA0, PA1 and PA2 pins are all tied high for 10 sec-
onds. Then, a power cycle of the board is mandatory.
The SAM-BA Boot Assistant is a default Boot Program that provides an easy way to program in situ the on-chip Flash
memory.
The SAM-BA Boot Assistant supports serial communication through the DBGU or through the USB Device Port. (The
SAM7S32/16 have no USB Device Port.)
Communication through the DBGU supports a wide range of crystals from 3 to 20 MHz via software auto-
detection.
Communication through the USB Device Port is limited to an 18.432 MHz crystal. (
The SAM-BA Boot provides an interface with SAM-BA Graphic User Interface (GUI).
9.
System Controller
The System Controller manages all vital blocks of the microcontroller: interrupts, clocks, power, time, debug and reset.
The System Controller peripherals are all mapped to the highest 4 Kbytes of address space, between addresses 0xFFFF
F000 and 0xFFFF FFFF.
Figure 9-1 on page 26 and Figure 9-2 on page 27 show the product specific System Controller Block Diagrams.
Figure 8-1 on page 20 shows the mapping of the of the User Interface of the System Controller peripherals. Note that the
memory controller configuration user interface is also mapped within this address space.
相關PDF資料
PDF描述
DSPIC33FJ32GS608-I/PT IC MCU/DSP 32KB FLASH 80TQFP
AT91SAM7XC256-CU-999 IC MCU ARM7 256KB FLASH 100TFBGA
AT91SAM7X256-CU-999 IC MCU ARM7 256KB FLASH 100TFBGA
DSPIC33FJ64MC802-E/SO IC DSPIC MCU/DSP 64K 28-SOIC
AT91SAM7S512-AU-999 IC MCU ARM7 512KB FLASH 64LQFP
相關代理商/技術參數
參數描述
AT91SAM7S64 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91 ARM Thumb-based Microcontrollers
AT91SAM7S64_05 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91 ARM Thumb-based Microcontrollers
AT91SAM7S64-AI 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91 ARM THUMB BASED MICROCONTROLLERS
AT91SAM7S64-AU-001 功能描述:ARM微控制器 - MCU LQFP IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
AT91SAM7S64-AU-999 功能描述:ARM微控制器 - MCU Microcontroller RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT