參數資料
型號： AT91SAM7X256-CU-999
廠商： Atmel
文件頁數： 15/44頁
文件大?。?/td> 0K
描述： IC MCU ARM7 256KB FLASH 100TFBGA
產品培訓模塊： SAM9 MPU Boot Solutions & Application Deployment
AT91SAM7X and SAM7XC Flash-based Microcontrollers
MCU Product Line Introduction
標準包裝： 3,000
系列： SAM7X
核心處理器： ARM7
芯體尺寸： 16/32-位
速度： 55MHz
連通性： CAN，以太網，I²C，SPI，SSC，UART/USART，USB
外圍設備： 欠壓檢測/復位，DMA，POR，PWM，WDT
輸入/輸出數： 62
程序存儲器容量： 256KB（256K x 8）
程序存儲器類型： 閃存
RAM 容量： 64K x 8
電壓 - 電源 (Vcc/Vdd)： 1.65 V ~ 1.95 V
數據轉換器： A/D 8x10b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 100-TFBGA
包裝： 帶卷 (TR)
配用： AT91SAM-ICE-ND - EMULATOR FOR AT91 ARM7/ARM9
AT91SAM7X-EK-ND - KIT EVAL FOR AT91SAM7X256/128
22
6120GS–ATARM–07-Apr-11
SAM7X512/256/128 Summary
after a full flash erase is performed. When the security bit is deactivated, all accesses to the
flash are permitted.
It is important to note that the assertion of the ERASE pin should always be longer than 220 ms.
As the ERASE pin integrates a permanent pull-down, it can be left unconnected during normal
operation. However, it is safer to connect it directly to GND for the final application.
8.5.5
Non-volatile Brownout Detector Control
Two general purpose NVM (GPNVM) bits are used for controlling the brownout detector (BOD),
so that even after a power loss, the brownout detector operations remain in their state.
These two GPNVM bits can be cleared or set respectively through the commands “Clear Gen-
eral-purpose NVM Bit” and “Set General-purpose NVM Bit” of the EFC User Interface.
GPNVM Bit 0 is used as a brownout detector enable bit. Setting the GPNVM Bit 0 enables
the BOD, clearing it disables the BOD. Asserting ERASE clears the GPNVM Bit 0 and thus
disables the brownout detector by default.
The GPNVM Bit 1 is used as a brownout reset enable signal for the reset controller. Setting
the GPNVM Bit 1 enables the brownout reset when a brownout is detected, Clearing the
GPNVM Bit 1 disables the brownout reset. Asserting ERASE disables the brownout reset by
default.
8.5.6
Calibration Bits
Eight NVM bits are used to calibrate the brownout detector and the voltage regulator. These bits
are factory configured and cannot be changed by the user. The ERASE pin has no effect on the
calibration bits.
8.6
Fast Flash Programming Interface
The Fast Flash Programming Interface allows programming the device through either a serial
JTAG interface or through a multiplexed fully-handshaked parallel port. It allows gang-program-
ming with market-standard industrial programmers.
The FFPI supports read, page program, page erase, full erase, lock, unlock and protect
commands.
The Fast Flash Programming Interface is enabled and the Fast Programming Mode is entered
when the TST pin and the PA0 and PA1 pins are all tied high.
8.7
SAM-BA Boot Assistant
The SAM-BA Boot Assistant is a default Boot Program that provides an easy way to program in-
situ the on-chip Flash memory.
The SAM-BA Boot Assistant supports serial communication via the DBGU or the USB Device
Port.
Communication via the DBGU supports a wide range of crystals from 3 to 20 MHz via
software auto-detection.
Communication via the USB Device Port is limited to an 18.432 MHz crystal.
The SAM-BA Boot provides an interface with SAM-BA Graphic User Interface (GUI).
The SAM-BA Boot is in ROM and is mapped at address 0x0 when the GPNVM Bit 2 is set to 0.
When GPNVM bit 2 is set to 1, the device boots from the Flash.
When GPNVM bit 2 is set to 0, the device boots from ROM (SAM-BA).
相關PDF資料
PDF描述
DSPIC33FJ64MC802-E/SO IC DSPIC MCU/DSP 64K 28-SOIC
AT91SAM7S512-AU-999 IC MCU ARM7 512KB FLASH 64LQFP
DSPIC30F4012-30I/SP IC DSPIC MCU/DSP 48K 28DIP
AT91SAM7XC128-CU-999 IC MCU ARM7 128KB FLASH 100TFBGA
AT91SAM7X128-CU-999 IC MCU ARM7 128KB FLASH 100TFBGA
相關代理商/技術參數
參數描述
AT91SAM7X512 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91 ARM Thumb-based Microcontrollers
AT91SAM7X512_07 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Incorporates the ARM7TDMI ARM Thumb Processor
AT91SAM7X512_09 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91 ARM Thumb-based Microcontrollers
AT91SAM7X512_1 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:AT91 ARM Thumb-based Microcontrollers
AT91SAM7X512-AU 功能描述:ARM微控制器 - MCU 512kB Flash 128kB SRAM 55MHz 4 PWM RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*