- 您現在的位置：買賣IC網 > PDF目錄3826 > AT91SAM7XC256B-CU-999 (Atmel)IC MCU ARM7 256KB FLASH 100TFBGA PDF資料下載
參數資料
| 型號： | AT91SAM7XC256B-CU-999 |
| 廠商： | Atmel |
| 文件頁數： | 16/47頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU ARM7 256KB FLASH 100TFBGA |
| 產品培訓模塊： | SAM9 MPU Boot Solutions & Application Deployment AT91SAM7X and SAM7XC Flash-based Microcontrollers MCU Product Line Introduction |
| 標準包裝： | 3,000 |
| 系列： | SAM7XC |
| 核心處理器： | ARM7 |
| 芯體尺寸： | 16/32-位 |
| 速度： | 55MHz |
| 連通性： | CAN，以太網，I²C，SPI，SSC，UART/USART，USB |
| 外圍設備： | 欠壓檢測/復位，DMA，POR，PWM，WDT |
| 輸入/輸出數： | 62 |
| 程序存儲器容量： | 256KB（256K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 64K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 1.65 V ~ 1.95 V |
| 數據轉換器： | A/D 8x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 100-TFBGA |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
23
6209DS–ATARM–17-Feb-09
AT91SAM7XC512/256/128
Flash Programming Interface, is forbidden. This ensures the confidentiality of the code pro-
grammed in the Flash.
This security bit can only be enabled, through the Command “Set Security Bit” of the EFC User
Interface. Disabling the security bit can only be achieved by asserting the ERASE pin at 1, and
after a full flash erase is performed. When the security bit is deactivated, all accesses to the
flash are permitted.
It is important to note that the assertion of the ERASE pin should always be longer than 220 ms.
As the ERASE pin integrates a permanent pull-down, it can be left unconnected during normal
operation. However, it is safer to connect it directly to GND for the final application.
8.5.5
Non-volatile Brownout Detector Control
Two general purpose NVM (GPNVM) bits are used for controlling the brownout detector (BOD),
so that even after a power loss, the brownout detector operations remain in their state.
These two GPNVM bits can be cleared or set respectively through the commands “Clear Gen-
eral-purpose NVM Bit” and “Set General-purpose NVM Bit” of the EFC User Interface.
GPNVM Bit 0 is used as a brownout detector enable bit. Setting the GPNVM Bit 0 enables
the BOD, clearing it disables the BOD. Asserting ERASE clears the GPNVM Bit 0 and thus
disables the brownout detector by default.
The GPNVM Bit 1 is used as a brownout reset enable signal for the reset controller. Setting
the GPNVM Bit 1 enables the brownout reset when a brownout is detected, Clearing the
GPNVM Bit 1 disables the brownout reset. Asserting ERASE disables the brownout reset by
default.
8.5.6
Calibration Bits
Eight NVM bits are used to calibrate the brownout detector and the voltage regulator. These bits
are factory configured and cannot be changed by the user. The ERASE pin has no effect on the
calibration bits.
8.6
Fast Flash Programming Interface
The Fast Flash Programming Interface allows programming the device through either a serial
JTAG interface or through a multiplexed fully-handshaked parallel port. It allows gang-program-
ming with market-standard industrial programmers.
The FFPI supports read, page program, page erase, full erase, lock, unlock and protect
commands.
The Fast Flash Programming Interface is enabled and the Fast Programming Mode is entered
when the TST pin and the PA0 and PA1 pins are all tied high.
8.7
SAM-BA Boot Assistant
The SAM-BA Boot Assistant is a default Boot Program that provides an easy way to program in-
situ the on-chip Flash memory.
The SAM-BA Boot Assistant supports serial communication via the DBGU or the USB Device
Port.
Communication via the DBGU supports a wide range of crystals from 3 to 20 MHz via
software auto-detection.
相關PDF資料 |
PDF描述 |
|---|---|
| AT91SAM7XC256B-AU-999 | IC MCU ARM7 256KB FLASH 100LQFP |
| AT91SAM7XC128B-CU-999 | IC MCU ARM7 128KB FLASH 100TFBGA |
| AT91SAM7XC128B-AU-999 | IC MCU ARM7 128KB FLASH 100LQFP |
| AT89LP828-PU | IC MCU 8051 8KB FLASH 28PDIP |
| MP2-HS192-42 | CONN SHROUD 2-FB 192POS 4ROW |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AT91SAM7XC256-CU | 功能描述:ARM微控制器 - MCU BGA IND TEMP RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| AT91SAM7XC256-CU-999 | 功能描述:ARM微控制器 - MCU BGA Ind. Temp Green RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT |
| AT91SAM7XC258 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:ARM Thumb-based Microcontrollers |
| AT91SAM7XC512 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Incorporates the ARM7TDMI ARM Thumb? Processor |
| AT91SAM7XC512_08 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:Incorporates the ARM7TDMI ARM Thumb? Processor |
發布緊急采購，3分鐘左右您將得到回復。