- 您現在的位置：買賣IC網 > PDF目錄67389 > ATS535JSB PROXIMITY SENSOR-HALL EFFECT, 65-95mA, ROUND, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | ATS535JSB |
| 元件分類： | 速度傳感器和接近開關 |
| 英文描述： | PROXIMITY SENSOR-HALL EFFECT, 65-95mA, ROUND, THROUGH HOLE MOUNT |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 90K |
| 代理商： | ATS535JSB |
ATS535JSB AND ATS535SSB
PROGRAMMABLE, TRUE
POWER-ON, HALL-EFFECT
PROXIMITY SENSORS
5
www.allegromicro.com
FUNCTIONAL DESCRIPTION
Dwg. EH-012
REG
SAMPLE
&
HOLD
X
+V
HALL
VOLTAGE
B
+
—
Dwg. AH-011-2
+B
0
OUTPUT
VOLTAGE
FLUX DENSITY
Dwg. GH-007-2
0
RP
B
VOUT(SAT)
CC
V
OP
B
+V
Chopper-Stabilized Technique. These devices use a
proprietary dynamic offset cancellation technique, with an
internal high-frequency clock to reduce the residual offset
voltage of the Hall element that is normally caused by
device overmolding, temperature dependencies, and
thermal stress. This technique produces devices that have
an extremely stable quiescent Hall output voltage, are
immune to thermal stress, and have precise recoverability
after temperature cycling. This technique will also slightly
degrade the device output repeatability.
The Hall element can be considered as a resistor array
similar to a Wheatstone bridge. A large portion of the
offset is a result of the mismatching of these resistors. The
chopper-stabilizing technique cancels the mismatching of
the resistors by changing the direction of the current
flowing through the Hall plate and Hall voltage measure-
ment taps, while maintaining the Hall-voltage signal that is
induced by the external magnetic flux. The signal is, then,
captured by a sample-and-hold circuit.
Operation. The output of these devices switches low
(turns ON) when a magnetic field (south pole) perpendicu-
lar to the Hall sensor exceeds the operate point threshold
(B
OP). After turn-ON, the output is capable of sinking 25
mA and the output voltage is V
OUT(SAT). When the mag-
netic field is reduced below the release point (B
RP), the
device output goes high (turns OFF). The difference in the
magnetic operate and release points is the hysteresis (B
hys)
of the device. This built-in hysteresis allows clean switch-
ing of the output even in the presence of external mechani-
cal vibration and electrical noise.
Applications. It is strongly recommended that an
external bypass capacitor be connected (in close proximity
to the Hall sensor) between the supply and ground of the
device to reduce both external noise and noise generated
by the chopper-stabilization technique.
Many other methods of operation are possible. Exten-
sive applications information on magnets and Hall-effect
sensors is also available in the Allegro Electronic Data
Book AMS-702 or Application Note 27701, or
www.allegromicro.com
相關PDF資料 |
PDF描述 |
|---|---|
| ATS611LSB | PROXIMITY SENSOR-HALL EFFECT, 0.5-2.5mm, 0.40V, ROUND, THROUGH HOLE MOUNT |
| ATS660LSB | PROXIMITY SENSOR-HALL EFFECT, 0.5-2.5mm, 0.40V, ROUND, THROUGH HOLE MOUNT |
| ATS622LSB | PROXIMITY SENSOR-HALL EFFECT, 0.5-2.5mm, 0.50%, 0.40V, ROUND, THROUGH HOLE MOUNT |
| ATS610LSA | PROXIMITY SENSOR-HALL EFFECT, 0.5-2.5mm, 0.40V, ROUND, THROUGH HOLE MOUNT |
| ATS612LSB | PROXIMITY SENSOR-HALL EFFECT, 0.4-2.5mm, 0.40V, ROUND, THROUGH HOLE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS-54150D-C0-R0 | 功能描述:HEATSINK 15X15X9.5MM W/OUT TIM RoHS:是 類別:風扇，熱管理 >> 熱敏 - 散熱器 系列:- 產品目錄繪圖:BDN12-3CB^A01 標準包裝:300 系列:BDN 類型:頂部安裝 冷卻式包裝:分類（BGA，LGA，CPU，ASIC……） 固定方法:散熱帶，粘合劑（含） 形狀:方形，鰭片 長度:1.21"（30.73mm） 寬:1.210"（30.73mm） 直徑:- 機座外的高度（散熱片高度）:0.355"（9.02mm） 溫升時的功耗:- 在強制氣流下的熱敏電阻:在 400 LFM 時為6.8°C/W 自然環境下的熱電阻:19.6°C/W 材質:鋁 材料表面處理:黑色陽極化處理 產品目錄頁面:2681 (CN2011-ZH PDF) 其它名稱:294-1099 |
| ATS-54150D-C1-R0 | 功能描述:Heat Sink BGA Aluminum Top Mount 制造商:advanced thermal solutions inc. 系列:- 零件狀態:有效 類型:頂部安裝 冷卻封裝:BGA 接合方法:散熱帶，粘合劑（含） 形狀:方形，鰭片 長度:0.590"（14.99mm） 寬度:0.590"（14.99mm） 直徑:- 離基底高度（鰭片高度）:0.374"（9.50mm） 不同溫升時功率耗散:- 不同強制氣流時的熱阻:26.2°C/W @ 200 LFM 自然條件下熱阻:- 材料:鋁 材料鍍層:黑色陽極化處理 標準包裝:10 |
| ATS-54150D-C2-R0 | 功能描述:HEAT SINK 15MM X 15MM X 9.5MM RoHS:是 類別:風扇，熱管理 >> 熱敏 - 散熱器 系列:- 標準包裝:500 系列:- 其它名稱:AE10843 |
| ATS-54150K-C0-R0 | 功能描述:HEATSINK 15X15X14.5MM W/OUT TIM RoHS:是 類別:風扇，熱管理 >> 熱敏 - 散熱器 系列:- 產品目錄繪圖:BDN12-3CB^A01 標準包裝:300 系列:BDN 類型:頂部安裝 冷卻式包裝:分類（BGA，LGA，CPU，ASIC……） 固定方法:散熱帶，粘合劑（含） 形狀:方形，鰭片 長度:1.21"（30.73mm） 寬:1.210"（30.73mm） 直徑:- 機座外的高度（散熱片高度）:0.355"（9.02mm） 溫升時的功耗:- 在強制氣流下的熱敏電阻:在 400 LFM 時為6.8°C/W 自然環境下的熱電阻:19.6°C/W 材質:鋁 材料表面處理:黑色陽極化處理 產品目錄頁面:2681 (CN2011-ZH PDF) 其它名稱:294-1099 |
| ATS-54150K-C1-R0 | 制造商:ATS 制造商全稱:Advanced Thermal Solutions, Inc. 功能描述:High Performance Extrusion, T412, BLACK-ANODIZED |
發布緊急采購，3分鐘左右您將得到回復。