- 您現在的位置：買賣IC網 > PDF目錄67389 > ATS611LSB PROXIMITY SENSOR-HALL EFFECT, 0.5-2.5mm, 0.40V, ROUND, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | ATS611LSB |
| 元件分類： | 速度傳感器和接近開關 |
| 英文描述： | PROXIMITY SENSOR-HALL EFFECT, 0.5-2.5mm, 0.40V, ROUND, THROUGH HOLE MOUNT |
| 封裝： | PLASTIC PACKAGE-4 |
| 文件頁數： | 4/17頁 |
| 文件大?。?/td> | 193K |
| 代理商： | ATS611LSB |
ATS660LSB
TRUE ZERO-SPEED,
HALL-EFFECT ADAPTIVE
GEAR-TOOTH SENSOR
www.allegromicro.com
11
APPLICATIONS INFORMATION — Continued
A
Dwg. MH-018-5 mm
A
2.2
α
TARGET FACE WIDTH, F
>2.2 SIN
α
2.2
COS
α
Recommended evaluation technique. The self-
calibrating feature of the ATS660LSB requires that a
special evaluation technique be used to measure its high-
accuracy performance capabilities. Installation inaccura-
cies are calibrated out at power on; hence, it is extremely
important that the device be repowered at each air gap
when gathering duty cycle data.
The ATS660LSB is designed to minimize performance
variation (caused by the large air-gap variations resulting
from installation) by self-calibrating at power-on. These
functions should be tested using the procedures described
below.
Duty cycle capabilities after correct self-calibration can
be measured as follows:
1. Set the air gap to the desired value.
2. Power down and then power up the device.
3. Rotate the gear at the desired speed.
4. Wait for calibration to complete (64 output pulses to
occur).
5. Monitor output for correct switching and measure
accuracy.
6. Repeat the above for multiple air gaps within the
operating range of the device.
7. This can be repeated over the entire operating tem-
perature range.
There is an internal update algorithm that will maintain
the correct duty cycle as air gap changes with temperature.
Large changes in air gap will require the part to be reset
(by cycling power) to maintain the correct duty cycle.
Measurement of the effect of changing air gap after
power up:
1. Set the air gap to the desired value (nominal, for
example). Rotate the gear at the desired speed. Apply
power to the module. Wait for 64 output pulses to occur.
Monitor output for correct switching and measure accu-
racy.
2. Change the air gap by
±0.25 mm. Do not re-power the
module. Wait for update algorithm to finish adjusting
thresholds, typically 1 to 2 rotations on a 60-tooth gear.
Operation with fine-pitch gears. For targets with a
circular pitch of less than 4mm, a performance improve-
ment can be observed by rotating the front face of the
sensor. This sensor rotation decreases the effective
sensor-to-sensor spacing and increases the capability of
detecting fine tooth or valley configurations, provided that
the Hall elements are not rotated beyond the width of the
target.
Allegro
相關PDF資料 |
PDF描述 |
|---|---|
| ATS660LSB | PROXIMITY SENSOR-HALL EFFECT, 0.5-2.5mm, 0.40V, ROUND, THROUGH HOLE MOUNT |
| ATS622LSB | PROXIMITY SENSOR-HALL EFFECT, 0.5-2.5mm, 0.50%, 0.40V, ROUND, THROUGH HOLE MOUNT |
| ATS610LSA | PROXIMITY SENSOR-HALL EFFECT, 0.5-2.5mm, 0.40V, ROUND, THROUGH HOLE MOUNT |
| ATS612LSB | PROXIMITY SENSOR-HALL EFFECT, 0.4-2.5mm, 0.40V, ROUND, THROUGH HOLE MOUNT |
| ATS612LSG | PROXIMITY SENSOR-HALL EFFECT, 0.4-2.25mm, 0.90%, 0.18-0.40V, THROUGH HOLE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS-61270D-C1-R0 | 功能描述:散熱片 FANSINK ASSY 26.25X26.25X9.5 (MM) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
| ATS-61270K-C1-R0 | 功能描述:散熱片 FANSINK ASSY 26.25 X 26.25 X 14.5 (MM) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
| ATS-61270R-C1-R0 | 功能描述:散熱片 FANSINK ASSY 26.25 X 26.25 X 19.5 (MM) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
| ATS-61270W-C1-R0 | 功能描述:散熱片 FANSINK ASSY 26.25 X 26.25 X 24.5 (MM) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
| ATS-61290D-C1-R0 | 功能描述:散熱片 FANSINK ASSY 28.25X28.25X9.5 (MM) RoHS:否 制造商:Ampro By ADLINK 產品:Heat Sink Accessories 安裝風格:Through Hole 散熱片材料: 散熱片樣式: 熱阻: 長度: 寬度: 高度: 設計目的:Express-HRR |
發布緊急采購，3分鐘左右您將得到回復。