- 您現在的位置：買賣IC網 > Datasheet目錄60 > ATS645LSHTN-I1 (Allegro Microsystems Inc)IC SENSOR GEAR TOOTH 4-SIP Datasheet資料下載
參數資料
| 型號： | ATS645LSHTN-I1 |
| 廠商： | Allegro Microsystems Inc |
| 文件頁數： | 10/14頁 |
| 文件大?。?/td> | 381K |
| 描述： | IC SENSOR GEAR TOOTH 4-SIP |
| 標準包裝： | 800 |
| 傳感范圍： | 120mV 跳閘，120mV 釋放 |
| 類型： | 專用型 |
| 電源電壓： | 4 V ~ 24 V |
| 電流 - 電源： | 8mA |
| 輸出類型： | 數字，開路集電極 |
| 特點： | 輪齒類型 |
| 工作溫度： | -40°C ~ 150°C |
| 封裝/外殼： | 4-SIP |
| 供應商設備封裝： | 4-SIP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁
True Zero Speed Miniature Differential Peak-
Detecting Gear Tooth Sensor IC
ATS645LSH
9
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Automatic Gain Control (AGC)
This feature allows the device to operate with an optimal internal
electrical signal, regardless of the air gap (within the AG speci-
cation). During calibration, the device determines the peak-to-
peak amplitude of the signal generated by the target. The gain
of the IC is then automatically adjusted. Figure 5 illustrates the
effect of this feature.
Automatic Offset Adjust (AOA)
The AOA is patented circuitry that automatically cancels the
effects of chip, magnet, and installation offsets. (For capability,
see Dynamic Offset Cancellation, in the Operating Characteris-
tics table.) This circuitry is continuously active, including both
during calibration mode and running mode, compensating for
any offset drift. Continuous operation also allows it to compen-
sate for offsets induced by temperature variations over time.
Digital Peak Detection
A digital DAC tracks the internal analog voltage signal V
PROC
,
and is used for holding the peak value of the internal analog
signal. In the example shown in gure 6, the DAC would rst
track up with the signal and hold the upper peaks value. When
V
PROC
drops below this peak value by B
OP
, the device hyster-
esis, the output would switch and the DAC would begin tracking
the signal downward toward the negative V
PROC
peak. Once the
DAC acquires the negative peak, the output will again switch
states when V
PROC
is greater than the peak by the value B
RP
. At
this point, the DAC tracks up again and the cycle repeats. The
digital tracking of the differential analog signal allows the IC to
achieve true zero-speed operation.
Figure 5. Automatic Gain Control (AGC). The AGC function corrects for
variances in the air gap. Differences in the air gap affect the magnetic
gradient, but AGC prevents that from affecting device performance, a
shown in the lowest panel.
Mechanical Profile
AG
Small
AG
Large
AG
Small
AG
Large
Internal Differential
Analog Signal
Response, with AGC
Internal Differential
Analog Signal
Response, without AGC
Ferrous Target
V+
V+
Figure 6: Peak Detecting Switchpoint Detail
Device
Output Current
B
RP
Internal
Differential
Analog Signal
V+
I+
B
OP
相關PDF資料 |
PDF描述 |
|---|---|
| ATS667LSGTN-T | IC SENSOR GEAR TOOTH 4SIP |
| ATS674LSETN-LT-T | IC SENSOR GEAR TOOTH 4-SIP |
| ATS682LSHTN-T | IC HALL EFFECT SENSOR 4SIP |
| ATS685LSHTN-T | IC HALL EFFECT GEAR SENSOR 4SIP |
| BU52001GUL-E2 | IC HALL EFFECT SW BIPO VCSP50L1 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS645LSHTN-I1-T | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:True Zero Speed Miniature Gear Tooth Sensor |
| ATS645LSHTN-I2-T | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:True Zero Speed Miniature Gear Tooth Sensor |
| ATS651LSH | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Two-Wire Self-Calibrating Differential Speed and Direction Sensor with Vibration Immunity |
| ATS651LSH_05 | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Two-Wire Self-Calibrating Differential Speed and Direction Sensor with Vibration Immunity |
| ATS651LSHTN-T | 制造商:Allegro MicroSystems LLC 功能描述:GEAR TOOTH SENSOR 2-WIRE SH MODULE |
發布緊急采購，3分鐘左右您將得到回復。