- 您現在的位置：買賣IC網 > PDF目錄67389 > ATS682LSHTN-T MAGNETIC FIELD SENSOR-HALL EFFECT, 3-100mT, CYLINDRICAL, THROUGH HOLE MOUNT PDF資料下載
參數資料
| 型號： | ATS682LSHTN-T |
| 元件分類： | 磁阻傳感器 |
| 英文描述： | MAGNETIC FIELD SENSOR-HALL EFFECT, 3-100mT, CYLINDRICAL, THROUGH HOLE MOUNT |
| 封裝： | LEAD FREE, PLASTIC, SIP-4 |
| 文件頁數： | 4/16頁 |
| 文件大小： | 319K |
| 代理商： | ATS682LSHTN-T |
Miniature, Two-Wire, True Zero Speed
Differential Peak-Detecting Sensor IC
ATS682LSH
12
Allegro MicroSystems, Inc.
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000; www.allegromicro.com
Device Operation
Power-On
When power (VCC > VCC(min)) is applied to the
device, a short period of time is required to activate the various
portions of the IC. During this period, the ATS682 powers-on in
the high current state, ICC(HIGH). After power-on, there are condi-
tions that could induce a change in the output state. Such an event
could be caused by thermal transients, but it would also require a
static applied magnetic field, proper signal polarity, and particular
direction and magnitude of internal signal drift.
Initial Offset Adjust
The IC initially compensates for differ-
ential offset, ΔBAPP, that results from chip, magnet, and instal-
lation alignment. Once the effective differential magnetic offset
has been cancelled, the digital tracking DAC is ready to track the
signal and provide output switching.
The period of time required for both power-on and initial offset
adjust is defined as the Power-On Time specification.
Calibration Mode
The calibration mode allows the IC to auto-
matically select the proper signal gain and continue to adjust for
DC differential magnetic offset. The AGC is active, and selects
the optimal signal gain based on the amplitude of the VPROC
signal. Following each adjustment to the AGC DAC, the Offset
DAC is also adjusted to ensure the internal analog signal is prop-
erly centered. During this mode, the tracking DAC is active and
output switching occurs, but the duty cycle is not guaranteed to
be within specification.
Running Mode
After the initial calibration process (CALI
edges) establishes a signal gain, the device moves to Running
mode. During Running mode, the IC tracks the input signal and
continues to give an output edge for every peak of the signal.
AOA remains active to compensate for any offset drift over time.
The ATS682 also incorporates an algorithm for adjusting the
signal gain during Running mode. This algorithm is designed to
optimize the VPROC signal amplitude in instances where the mag-
netic signal during the calibration period is not representative of
the amplitude of the magnetic signal for the installed application
air gap (see figure 9).
IC Electrical
Output, I
OUT
Internal Differential
Signal, V
PROC
BRP
BOP
BRP
1
2
3
4
5
Figure 9: Operation of Running Mode Gain Adjust.
Position 1. The device is initially powered-on. Self-calibration occurs.
Position 2. Small amplitude oscillation of the target sends an erroneously small differential signal to the device. The amplitude of VPROC is greater than
the switching hysteresis (BOP and BRP), and the device output switches.
Position 3. The calibration period completes on the third rising output edge, and the device enters Running mode.
Position 4. True target rotation occurs and the correct magnetic signal is generated for the installation air gap. The established signal gain is too large for
the rotational magnetic signal of the target, at the given air gap.
Position 5. Running mode calibration corrects the signal gain to an optimal level for the installation air gap.
相關PDF資料 |
PDF描述 |
|---|---|
| ATS685LSHTN-T | MAGNETIC FIELD SENSOR-HALL EFFECT, 5-150mT, CYLINDRICAL, THROUGH HOLE MOUNT |
| AU-1293-140 | 100 MHz - 180 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| AM-3A-000515 | 5 MHz - 1500 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| AU-1241-70 | 50 MHz - 90 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER |
| AUP-1479 | 5 MHz - 300 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ATS684LSNTN-T | 功能描述:TWO-WIRE DIFF SPEED SENSOR IC WI 制造商:allegro microsystems, llc 系列:- 包裝:剪切帶（CT） 零件狀態:在售 功能:專用型 技術:霍爾效應 極化:單向 感應范圍:70% 跳閘，30% 釋放 測試條件:25°C 電壓 - 電源:4 V ~ 24 V 電流 - 電源（最大值）:16mA 電流 - 輸出（最大值）:- 輸出類型:電流源 特性:- 工作溫度:-40°C ~ 150°C 封裝/外殼:3-SIP 供應商器件封裝:3-SIP 標準包裝:1 |
| ATS685LSH | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Two-Wire, Zero Speed Differential Gear Tooth Sensor IC |
| ATS685LSHTN-T | 功能描述:IC HALL EFFECT GEAR SENSOR 4SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:- 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| ATS692LSHTN-RSNPH-T | 功能描述:IC HALL EFFECT SENSOR 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:帶卷（TR） 零件狀態:有效 功能:專用型 技術:霍爾效應 極化:- 感應范圍:69% 跳閘，31% 釋放 測試條件:-40°C ~ 150°C 電壓 - 電源:4 V ~ 24 V 電流 - 電源（最大值）:16.5mA 電流 - 輸出（最大值）:- 輸出類型:電流 特性:- 工作溫度:-40°C ~ 150°C（TA） 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:800 |
| ATS693LSGTN-RSNYPH-T | 功能描述:IC HALL EFFECT SENSOR 4SIP 制造商:allegro microsystems, llc 系列:- 包裝:帶卷（TR） 零件狀態:有效 功能:專用型 技術:霍爾效應 極化:- 感應范圍:69% 跳閘，31% 釋放 測試條件:-40°C ~ 150°C 電壓 - 電源:4 V ~ 24 V 電流 - 電源（最大值）:16.5mA 電流 - 輸出（最大值）:- 輸出類型:電流 特性:- 工作溫度:-40°C ~ 150°C（TA） 封裝/外殼:4-SIP 模塊 供應商器件封裝:4-SIP 標準包裝:800 |
發布緊急采購，3分鐘左右您將得到回復。