參數資料
型號: ATSAM3N1AB-AU
廠商: Atmel
文件頁數: 13/60頁
文件大?。?/td> 0K
描述: IC MCU 64KB CORTEX-M3 48-LQFP
標準包裝: 250
系列: SAM3N
核心處理器: ARM? Cortex?-M3
芯體尺寸: 32-位
速度: 48MHz
連通性: I²C,IrDA,SPI,UART/USART
外圍設備: 欠壓檢測/復位,DMA,POR,PWM,WDT
輸入/輸出數: 34
程序存儲器容量: 64KB(64K x 8)
程序存儲器類型: 閃存
RAM 容量: 8K x 8
電壓 - 電源 (Vcc/Vdd): 1.62 V ~ 3.6 V
數據轉換器: A/D 8x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 48-LQFP
包裝: 托盤
20
11011BS–ATARM–22-Feb-12
SAM3N Summary
Supply Monitor alarm
RTC alarm
RTT alarm
5.5.2
Wait Mode
The purpose of the wait mode is to achieve very low power consumption while maintaining the
whole device in a powered state for a startup time of less than 10 s. Current Consumption in
Wait mode is typically 15 A (total current consumption) if the internal voltage regulator is used
or 8 A if an external regulator is used.
In this mode, the clocks of the core, peripherals and memories are stopped. However, the core,
peripherals and memories power supplies are still powered. From this mode, a fast start up is
available.
This mode is entered via Wait for Event (WFE) instructions with LPM = 1 (Low Power Mode bit in
PMC_FSMR). The Cortex-M3 is able to handle external or internal events in order to wake up
the core (WFE). By configuring the WUP0-15 external lines as fast startup wake-up pins (refer to
Section 5.7 “Fast Start-Up”). RTC or RTT Alarm wake-up events can be used to wake up the
CPU (exit from WFE).
Entering Wait Mode:
Select the 4/8/12 MHz fast RC oscillator as Main Clock
Set the LPM bit in the PMC Fast Startup Mode Register (PMC_FSMR)
Execute the Wait-For-Event (WFE) instruction of the processor
Note:
Internal Main clock resynchronization cycles are necessary between the writing of MOSCRCEN
bit and the effective entry in Wait mode. Depending on the user application, Waiting for
MOSCRCEN bit to be cleared is recommended to ensure that the core will not execute undesired
instructions.
5.5.3
Sleep Mode
The purpose of sleep mode is to optimize power consumption of the device versus response
time. In this mode, only the core clock is stopped. The peripheral clocks can be enabled. The
current consumption in this mode is application dependent.
This mode is entered via Wait for Interrupt (WFI) or Wait for Event (WFE) instructions with
LPM = 0 in PMC_FSMR.
The processor can be woke up from an interrupt if WFI instruction of the Cortex M3 is used, or
from an event if the WFE instruction is used to enter this mode.
相關PDF資料
PDF描述
VI-BWB-IW CONVERTER MOD DC/DC 95V 100W
VI-BW4-IX CONVERTER MOD DC/DC 48V 75W
VI-B2X-IW CONVERTER MOD DC/DC 5.2V 100W
VI-B20-IX CONVERTER MOD DC/DC 5V 75W
VI-B20-IW CONVERTER MOD DC/DC 5V 100W
相關代理商/技術參數
參數描述
ATSAM3N1AB-AUR 制造商:Atmel Corporation 功能描述:. - LQFP,GREEN,IND TEMP,MRL B,T&R - Tape and Reel 制造商:Atmel Corporation 功能描述:IC MCU 32BIT 64KB FLASH 48LQFP
ATSAM3N1AB-MU 功能描述:ARM微控制器 - MCU QFN,Grn, IT, MRL B RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
ATSAM3N1AB-MUR 制造商:Atmel Corporation 功能描述:. - QFN,GREEN,IND TEMP,MRL B,T&R - Tape and Reel 制造商:Atmel Corporation 功能描述:IC MCU 32BIT 64KB FLASH 48QFN
ATSAM3N1BA-AU 功能描述:ARM微控制器 - MCU IND TEMP MRLA RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT
ATSAM3N1BA-MU 功能描述:ARM微控制器 - MCU IND TEMP MRLA RoHS:否 制造商:STMicroelectronics 核心:ARM Cortex M4F 處理器系列:STM32F373xx 數據總線寬度:32 bit 最大時鐘頻率:72 MHz 程序存儲器大小:256 KB 數據 RAM 大小:32 KB 片上 ADC:Yes 工作電源電壓:1.65 V to 3.6 V, 2 V to 3.6 V, 2.2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:LQFP-48 安裝風格:SMD/SMT