參數資料
型號: ATTINY15L-1PC
廠商: Atmel
文件頁數: 32/85頁
文件大?。?/td> 0K
描述: IC AVR MCU 1K FLASH 2.7V 8DIP
標準包裝: 50
系列: AVR® ATtiny
核心處理器: AVR
芯體尺寸: 8-位
速度: 1.6MHz
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 6
程序存儲器容量: 1KB(512 x 16)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 64 x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 5.5 V
數據轉換器: A/D 4x10b
振蕩器型: 內部
工作溫度: 0°C ~ 70°C
封裝/外殼: 8-DIP(0.300",7.62mm)
包裝: 管件
38
ATtiny15L
1187H–AVR–09/07
The user should poll the EEWE bit before starting the read operation. If a write operation
is in progress when new data or address is written to the EEPROM I/O Registers, the
write operation will be interrupted and the result is undefined.
The calibrated oscillator is used to time EEPROM. In Table 16 the typical programming
time is listed for EEPROM access from the CPU.
Preventing EEPROM
Corruption
During periods of low V
CC, the EEPROM data can be corrupted because the supply volt-
age is too low for the CPU and the EEPROM to operate properly. These issues are the
same as for board-level systems using the EEPROM and the same design solutions
should be applied.
An EEPROM data corruption can be caused by two situations when the voltage is too
low. First, a regular write sequence to the EEPROM requires a minimum voltage to
operate correctly. Second, the CPU itself can execute instructions incorrectly if the sup-
ply voltage for executing instructions is too low.
EEPROM data corruption can easily be avoided by following these design recommen-
dations (one is sufficient):
1.
Keep the AVR RESET active (low) during periods of insufficient power supply
voltage. This can be done by enabling the internal Brown-out Detector (BOD) if
the operating voltage matches the detection level. If not, an external low V
CC
Reset Protection circuit can be applied.
2.
Keep the AVR core in Power-down sleep mode during periods of low V
CC. This
will prevent the CPU from attempting to decode and execute instructions, effec-
tively protecting the EEPROM Registers from unintentional writes.
3.
Store constants in Flash memory if the ability to change memory contents from
software is not required. Flash memory cannot be updated by the CPU and will
not be subject to corruption.
Table 16. Typical EEPROM Programming Times
Parameter
Number of Calibrated RC
Oscillator Cycles
Min Programming
Time
Max Programming
Time
EEPROM write
(from CPU)
8192
4.6 ms
8.2 ms
相關PDF資料
PDF描述
AT89C2051-24SI MICRO CONTROLLER
AT90S8515-8JC IC MCU 8K FLSH 8MHZ 44PLCC
PIC24FV16KA304-I/PT MCU 16KB FLASH 2KB RAM 44-TQFP
AT90S8515-8AC IC MCU 8K FLSH 8MHZ 44TQFP
PIC24FJ64GA002-E/SO IC PIC MCU FLASH 64K 28-SOIC
相關代理商/技術參數
參數描述
ATTINY15L-1PI 功能描述:8位微控制器 -MCU AVR 1K FLASH 64B EE ADC 3V 1.6MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY15L-1PU 功能描述:8位微控制器 -MCU AVR 1K FLASH 64B EE ADC 3V 1.6MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY15L-1SC 功能描述:8位微控制器 -MCU AVR 1K FLASH 64B EE ADC 3V 1.6MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY15L-1SC SL383 制造商:Atmel Corporation 功能描述:MCU 8-Bit ATtiny AVR RISC 1KB Flash 3.3V/5V 8-Pin SOIC EIAJ T/R
ATTINY15L-1SI 功能描述:8位微控制器 -MCU AVR 1K FLASH 64B EE ADC 3V 1.6MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT