參數資料
型號: ATTINY24A-PU
廠商: Atmel
文件頁數: 24/135頁
文件大?。?/td> 0K
描述: MCU AVR 2K FLASH 20MHZ 14PDIP
產品培訓模塊: MCU Product Line Introduction
tinyAVR Introduction
標準包裝: 25
系列: AVR® ATtiny
核心處理器: AVR
芯體尺寸: 8-位
速度: 20MHz
連通性: USI
外圍設備: 欠壓檢測/復位,POR,PWM,溫度傳感器,WDT
輸入/輸出數: 12
程序存儲器容量: 2KB(1K x 16)
程序存儲器類型: 閃存
EEPROM 大小: 128 x 8
RAM 容量: 128 x 8
電壓 - 電源 (Vcc/Vdd): 1.8 V ~ 5.5 V
數據轉換器: A/D 8x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 14-DIP(0.300",7.62mm)
包裝: 管件
配用: ATSTK600-RC12-ND - STK600 ROUTING CARD AVR
ATSTK505-ND - ADAPTER KIT FOR 14PIN AVR MCU
12
8183F–AVR–06/12
ATtiny24A/44A/84A
to be cleared. If an interrupt condition occurs while the corresponding interrupt enable bit is
cleared, the Interrupt Flag will be set and remembered until the interrupt is enabled, or the flag is
cleared by software. Similarly, if one or more interrupt conditions occur while the Global Interrupt
Enable bit is cleared, the corresponding Interrupt Flag(s) will be set and remembered until the
Global Interrupt Enable bit is set, and will then be executed by order of priority.
The second type of interrupts will trigger as long as the interrupt condition is present. These
interrupts do not necessarily have Interrupt Flags. If the interrupt condition disappears before the
interrupt is enabled, the interrupt will not be triggered.
When the AVR exits from an interrupt, it will always return to the main program and execute one
more instruction before any pending interrupt is served.
Note that the Status Register is not automatically stored when entering an interrupt routine, nor
restored when returning from an interrupt routine. This must be handled by software.
When using the CLI instruction to disable interrupts, the interrupts will be immediately disabled.
No interrupt will be executed after the CLI instruction, even if it occurs simultaneously with the
CLI instruction. The following example shows how this can be used to avoid interrupts during the
timed EEPROM write sequence.
Note:
Assembly Code Example
in
r16, SREG
; store SREG value
cli
; disable interrupts during timed sequence
sbi
EECR, EEMPE
; start EEPROM write
sbi
EECR, EEPE
out
SREG, r16
; restore SREG value (I-bit)
C Code Example
char
cSREG;
cSREG = SREG; /* store SREG value */
/* disable interrupts during timed sequence */
_CLI();
EECR |= (1<<EEMPE); /* start EEPROM write */
EECR |= (1<<EEPE);
SREG = cSREG; /* restore SREG value (I-bit) */
相關PDF資料
PDF描述
88910-011LF RAMPING MODULE W/SCREW
70295-001LF SHORT SINGLE GUIDE PIN
70295-004LF LONG DOUBLE METRAL GUIDE PIN
88914-013LF KEYING PIN WITH SCREW
88914-012LF KEYING PIN WITH SCREW
相關代理商/技術參數
參數描述
ATTINY24A-SSF 功能描述:8位微控制器 -MCU 2KB FL 128B EE SRAM USIADC 20MHz Hi+125C RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY24A-SSFR 功能描述:8位微控制器 -MCU 2KB FL 128B EE SRAM USIADC 20MHz Hi+125C RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY24A-SSN 功能描述:8位微控制器 -MCU 2K FLASH 128B EE 128B SRAM USI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY24A-SSNR 功能描述:8位微控制器 -MCU AVR 2KB FL 128B EE USI ADC 20MHz 105C RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY24A-SSU 功能描述:8位微控制器 -MCU 20MHz, Ind Temp 1.8-5.5V, Green RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT