參數資料
型號: ATtiny28L
廠商: Atmel Corp.
英文描述: 8-Bit AVR Microcontroller with 2K bytes Flash(8位AVR技術微控制器(帶2K字節閃速存儲器))
中文描述: 8位AVR微控制器與2K字節的閃存(8位AVR的技術微控制器(帶2K字節閃速存儲器))
文件頁數: 46/81頁
文件大?。?/td> 663K
代理商: ATTINY28L
50
ATtiny28L/V
1062F–AVR–07/06
1.
Set BS to “1”. This selects high data.
2.
Give WR a negative pulse. This starts programming of the data byte. RDY/BSY
goes low.
3.
Wait until RDY/BSY goes high to program the next byte.
(See Figure 39 for signal waveforms.)
The loaded command and address are retained in the device during programming. For
efficient programming, the following should be considered:
The command needs to be loaded only once when writing or reading multiple
memory locations.
Address high byte only needs to be loaded before programming a new 256-word
page in the Flash.
Skip writing the data value $FF, that is, the contents of the entire Flash after a Chip
Erase.
These considerations also apply to Flash and signature bytes reading.
Reading the Flash
The algorithm for reading the Flash memory is as follows (refer to “Programming the
Flash” for details on command and address loading):
A: Load Command “0000 0010”.
B: Load Address High Byte ($00 - $03).
C: Load Address Low Byte ($00 - $FF).
1.
Set OE to “0”, and BS to “0”. The Flash word low byte can now be read at DATA.
2.
Set BS to “1”. The Flash word high byte can now be read from DATA.
3.
Set OE to “1”.
Programming the Fuse Bits
The algorithm for programming the Fuse bits is as follows (refer to “Programming the
Flash” for details on command and data loading):
A: Load Command “0100 0000”.
D: Load Data Low Byte. Bit n = “0” programs and bit n = “1” erases the Fuse bit.
Bit 4 = INTCAP Fuse
Bit 3 = CKSEL3 Fuse
Bit 2 = CKSEL2 Fuse
Bit 1 = CKSEL1 Fuse
Bit 0 = CKSEL0 Fuse
Bits 7 - 5 = “1”. These bits are reserved and should be left unprogrammed (“1”).
E: Write Data Low Byte.
Programming the Lock Bits
The algorithm for programming the Lock bits is as follows (refer to “Programming the
Flash” for details on command and data loading):
A: Load Command “0010 0000”.
D: Load Data Low Byte. Bit n = “0” programs the Lock bit.
Bit 2 = Lock Bit2
Bit 1 = Lock Bit1
Bits 7 - 3,0 = “1”. These bits are reserved and should be left unprogrammed (“1”).
E: Write Data Low Byte.
The Lock bits can only be cleared by executing Chip Erase.
相關PDF資料
PDF描述
ATmega8535 -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash
ATMEGA32 8-bit AVR Microcontroller with 32K Bytes In-System Programmable Flash
ATmega64 -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash
ATMEGA8 -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash
ATMEGA8515 -bit AVR Microcontroller with 8K Bytes In- System Programmable Flash
相關代理商/技術參數
參數描述
ATTINY28L_06 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with 2K Bytes of Flash
ATTINY28L-4AC 功能描述:8位微控制器 -MCU AVR 2K FLASH 28 PIN PACKAGE - 3V 4MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY28L-4AI 功能描述:8位微控制器 -MCU AVR 2K FLASH 28 PIN PACKAGE - 3V 4MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY28L-4AU 功能描述:8位微控制器 -MCU AVR 2K FLASH 28 PIN PACKAGE - 3V 4MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ATTINY28L-4AUR 功能描述:8位微控制器 -MCU AVR 2K FL 4MHZ IND TEMP 3V RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT