參數資料
型號： AU-1241-70
廠商： MITEQ INC
元件分類： 放大器
英文描述： 50 MHz - 90 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER
文件頁數： 21/25頁
文件大小： 1906K
代理商： AU-1241-70
recorded over the operating frequency range. Unless
the amplifier is specified to operate over a defined
temperature range, this measurement is per-
formed at room ambient temperature (+23°C). If a
range of temperatures is specified, the measurement
must also be verified at the temperature extremes.
NOISE FIGURE
Noise figure is classically defined as:
Since all realistic amplifiers add thermal noise, the
signal-to-noise ratio at the output will be degraded;
therefore, noise figure will be a ratio greater than one,
or when expressed in decibels, a positive number
(NFdB = 10 log10(NFRatio). The additive noise of an
amplifier can also be expressed in a parameter
referred to as noise temperature. In this approach,
the noise temperature of the amplifier is equal to the
temperature (in degrees Kelvin) of a 50
termination
at the input of an ideal noiseless amplifier with the
same gain and generating the same output noise power.
The relationship between noise figure and noise tem-
perature is :
Noise figure data is measured at discrete frequencies
throughout the band at +23°C unless specified otherwise.
OUTPUT POWER AT 1 dB COMPRESSION
The 1 dB output compression point of an amplifier is
simply defined as the output power level at which the
gain deviates from the small signal gain by 1 dB.
All active components have a linear dynamic range.
This is the range over which the output power varies
linearly with respect to the input power. As the output
power increases to near its maximum capability, the
device will begin to saturate. The point at which the
saturation effects are 1 dB from linear is defined as
the 1 dB compression point. Because of the nonlin-
ear relation between the input and output power at
this point, the following relationship holds:
Pout 1 dB = Pin 1 dB + Linear Gain - 1 dB
BIPOLAR AMPLIFIERS
GENERAL SPECIFICATIONS
All models described in this catalog are classified by
several specifications, namely:
Operating Frequency Range
Gain
Gain Flatness
Noise Figure
Output Power at 1 dB Compression
Input and Output VSWR
DC Supply Voltage and Current Consumption
The following notes give detailed definitions to these
and additional specifications which may relate to your
system requirements.
OPERATING FREQUENCY RANGE
The operating frequency range is the range of fre-
quencies over which the amplifier will meet or exceed
the specification parameters. The amplifier may per-
form beyond this frequency range.
GAIN
Gain is defined as the ratio of the power measured at
the output of an amplifier to the power provided to the
input port. It is usually expressed in decibels and is
typically measured in a swept fashion across the
operating frequency range. The gain of all amplifiers
is verified by a swept measurement before shipment
from MITEQ.
GAIN FLATNESS
Gain flatness describes the variation in an amplifier's
gain over the operating frequency range at any fixed
temperature within the operating temperature range.
As such, it does not include the variation of gain as a
function of temperature (see Gain Variation vs.
Temperature).
The gain flatness of an amplifier is measured by view-
ing the swept gain and determining the difference
between the minimum gain and the maximum gain
SPECIFICATION DEFINITIONS
Peak-to-Peak Gain Flatness
Operating Frequency Range
(Measured at one temperature)
Max. Gain
Min. Gain
F Low
F High
4
Noise Figure =
=
Si/Ni
So/No
Signal-to-noise ratio
at the amplifier input
Signal-to-noise ratio
at the amplifier output
Noise Figure = 10 Log 10
{
+1
}
Noise Temperature (Kelvin)
290 Kelvin
相關PDF資料
PDF描述
AUP-1479 5 MHz - 300 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER
AM-1571-140 100 MHz - 180 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER
AM-1571-70 50 MHz - 90 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER
AU-2A-1241 50 MHz - 90 MHz RF/MICROWAVE NARROW BAND LOW POWER AMPLIFIER
AUP-1568 5 MHz - 200 MHz RF/MICROWAVE WIDE BAND MEDIUM POWER AMPLIFIER
相關代理商/技術參數
參數描述
AU125A473JA72A 功能描述:多層陶瓷電容器MLCC - SMD/SMT 50volts 0.047uF 5% C0G 1812 SIZE RoHS:否 制造商:American Technical Ceramics (ATC) 電容:10 pF 容差:1 % 電壓額定值:250 V 溫度系數/代碼:C0G (NP0) 外殼代碼 - in:0505 外殼代碼 - mm:1414 工作溫度范圍:- 55 C to + 125 C 產品:Low ESR MLCCs 封裝:Reel
AU1277BK1 制造商:Hubbell Wiring Device-Kellems 功能描述:WS SENS, US, 1 CIRC, BK
AU1277BK1N 制造商:Hubbell Wiring Device-Kellems 功能描述:SENSOR, MOTION, ULTRASONIC, 120V/277V; Detector Type:Ultrasonic; Sensing Range Max:400sq. ft; Beam Angle:180; Color:Black; Features:Auto control w/no button; Leaded Process Compatible:No; No. of Circuits:1 ;RoHS Compliant: No 制造商:Hubbell Wiring Device-Kellems 功能描述:WS SENS, US, 1 CIRC, NO BTN, BK
AU1277BK2 制造商:Hubbell Wiring Device-Kellems 功能描述:WS SENS, US, 2 CIRC, BK
AU1277BK2N 制造商:Hubbell Wiring Device-Kellems 功能描述:WS SENS, US, 2 CIRC, NO BTN, BK
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*