參數資料
型號： AZ7310
元件分類： 開關
英文描述： SNAP ACTING/LIMIT SWITCH, DPDT, MOMENTARY, 0.4A, 115VDC, 8mm, PANEL MOUNT-THREADED
封裝： ROHS COMPLIANT
文件頁數： 5/20頁
文件大?。?/td> 692K
代理商： AZ7310
8
α
Vmax (m/s)
CAUTIONS FOR USE
Pay attention to the following points
when designing the dog for limit switch
operation.
1. Make the dog faceplate as smooth
as possible.
2. Adjust both the dog angle and the
set arm angle as below, depending on
the operating speed.
3. The depth (h) of the dog effects the
lifespan of the limit switch. Therefore,
set the depth to a maximum of 80% of
the Total Travel (T.T.)
4. The relationship between the speed
of the dog (V = m/s) and the tip angle
(
α) is as follows:
1) V&0.2m/s
3) 0.5m/s ! V&2m/s
Because the arm jiggle is as a mini-
mum at a comparative speed such as
V&0.5m/s, setting both the dog angle
so that it travels perpendicularly and
the arm angle to 45° is optimum.
If overriding the dog, set the arm per-
pendicularly, so that
α =45°. If the dog
angle is reduced, the tolerable speed
is increased.
5) Roller plunger type
DESIGN OF OPERATING DOG AND OPERATING SPEED
When V&0.2m/s, set the arm to per-
pendicular and set the arm rise angle
to between 45° and 90°. If the dog rise
angle is reduced, the maximum tolera-
ble speed is increased.
As a rule,
α = 45° is optimum.
2) V&0.5m/s
The maximum tolerable speed can be
extended by further reducing the dog
rise angle from 45° when 0.5m/s !
V&2m/s. It is necessary to set the arm
so that the dog’s cutting surfaces are
always parallel (
θ o = 90°– α)
4) Overriding the dog (V&0.2m/s)
h
V
α = 45° to 90°
F
o
h
α
V
θ
F
h
V
α = 45°
o = 45
°
θ
h
α
h
α
45°
0.2
60°
0.1
60 to 90°
0.05
α
Vmax (m/s)
Even if overriding the dog, set the for-
wards and rearwards motion exactly
the same, and avoid any settings that
make the actuator accelerate rapidly
from the dog.
5. Operation speed
1) When the operation (acting and
reverting) speed is exceedingly slow,
switching of the contacts will become
unstable and this could cause prob-
lems such as failure to make contact
and welding. As a guide, the speed
should be at least 1mm/s.
2) When the operation (acting and
reverting) speed is exceedingly fast,
be careful because the violent motion
could cause breakage and with
increased frequency, contact switching
will not be able to keep up. As a guide,
the switching frequency should be
within 20 times per minute.
20°
0.5
30°
0.25
h
(0.5 to 0.7) T.T.
(0.6 to 0.8) T.T.
α
Vmax (m/s)
45°
0.2
60°
0.1
60 to 90°
0.05
α
Vmax (m/s)
40°
0.7
35°
0.9
30°
1.3
25°
2.0
相關PDF資料
PDF描述
AZ7411F SNAP ACTING/LIMIT SWITCH, DPDT, MOMENTARY, 0.4A, 115VDC, 17.5mm, PANEL MOUNT
AZ5105661 SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 6A, 24VDC, PANEL MOUNT
AZ5124162 SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 6A, 24VDC, PANEL MOUNT
AZ5128 SNAP ACTING/LIMIT SWITCH, SPST, MOMENTARY, 0.8A, 125VDC, PANEL MOUNT
AZ7461F SNAP ACTING/LIMIT SWITCH, DPDT, MOMENTARY, 0.4A, 115VDC, 36mm, PANEL MOUNT
相關代理商/技術參數
參數描述
AZ7310 制造商:Panasonic Electric Works 功能描述:LIMIT SWITCH PUSH PLUNGER SPDT
AZ7310CEJ 制造商:Panasonic Electric Works 功能描述:LIMIT SWITCH,PUSH PLUNGER
AZ7311 制造商:Panasonic Electric Works 功能描述:LIMIT SWITCH ROLLER PLUNGER SPDT 制造商:Panasonic Electric Works 功能描述:LIMIT SWITCH, ROLLER PLUNGER, SPDT 制造商:Panasonic Electric Works 功能描述:Switch Limit N.O./N.C. SPDT Top Roller Plunger Cable 10A 250VAC 115VDC 5.88N Linear Panel Mount/Screw Mount
AZ7311 制造商:Panasonic Electric Works 功能描述:LIMIT SWITCH ROLLER PLUNGER SPDT 制造商:Panasonic Electric Works 功能描述:LIMIT SWITCH, ROLLER PLUNGER, SPDT
AZ7311CEJ 制造商:Panasonic Electric Works 功能描述:limit switch, panel mount roller plunger
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*