- 您現在的位置：買賣IC網 > PDF目錄6115 > BA3472FV-E2 (Rohm Semiconductor)IC OPAMP DUAL 36V 4MA SSOP-B8 PDF資料下載
參數資料
| 型號： | BA3472FV-E2 |
| 廠商： | Rohm Semiconductor |
| 文件頁數： | 18/32頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP DUAL 36V 4MA SSOP-B8 |
| 標準包裝： | 1 |
| 放大器類型： | 通用 |
| 電路數： | 2 |
| 轉換速率： | 10 V/µs |
| 增益帶寬積： | 4MHz |
| 電流 - 輸入偏壓： | 100nA |
| 電壓 - 輸入偏移： | 1500µV |
| 電流 - 電源： | 4mA |
| 電流 - 輸出 / 通道： | 30mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 36 V，±1.5 V ~ 18 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-LSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 8-SSOP |
| 包裝： | 標準包裝 |
| 產品目錄頁面： | 1369 (CN2011-ZH PDF) |
| 其它名稱： | BA3472FV-E2DKR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Datasheet
www.rohm.com
TSZ02201-0RAR0G200100-1-2
2012 ROHM Co., Ltd. All rights reserved.
25/29
26.OCT.2012 Rev.002
TSZ2211115001
BA3472xxx, BA3472RFVM, BA3474xxx, BA3474RFV
●Operational Notes
1) Unused circuits
When there are unused circuits it is recommended that they are connected
as in Figure 54, setting the non-inverting input terminal to a potential within
input common-mode voltage range (Vicm).
2) Input terminal voltage
Applying GND + 36V to the input terminal is possible without causing
deterioration of the electrical characteristics or destruction, irrespective of
the supply voltage. However, this does not ensure normal circuit operation.
Please note that the circuit operates normally only when the input voltage is
within the common mode input voltage range of the electric characteristics.
3) Power supply (single / dual)
The op-amp operates when the specified voltage supplied is between VCC
and VEE. Therefore, the single supply op-amp can be used as dual supply
op-amp as well.
4) Power dissipation Pd
Using the unit in excess of the rated power dissipation may cause deterioration in electrical characteristics due to a rise in
chip temperature, including reduced current capability. Therefore, please take into consideration the power dissipation
(Pd) under actual operating conditions and apply a sufficient margin in thermal design. Refer to the thermal derating
curves for more information.
5) Short-circuit between pins and erroneous mounting
Incorrect mounting may damage the IC. In addition, the presence of foreign particles between the outputs, the output and
the power supply, or the output and GND may result in IC destruction.
6) Operation in a strong electromagnetic field
Operation in a strong electromagnetic field may cause malfunctions.
7) Radiation
This IC is not designed to withstand radiation.
8) IC handling
Applying mechanical stress to the IC by deflecting or bending the board may cause fluctuations in the electrical
characteristics due to piezo resistance effects.
9) Board inspection
Connecting a capacitor to a pin with low impedance may stress the IC. Therefore, discharging the capacitor after every
process is recommended. In addition, when attaching and detaching the jig during the inspection phase, ensure that the
power is turned OFF before inspection and removal. Furthermore, please take measures against ESD in the assembly
process as well as during transportation and storage.
10) Output capacitor
Discharge of the external output capacitor to VCC is possible via internal parasitic elements when VCC is shorted to VEE,
causing damage to the internal circuitry due to thermal stress. Therefore, when using this IC in circuits where oscillation
due to output capacitive load does not occur, such as in voltage comparators, use an output capacitor with a capacitance
less than 0.1F.
Status of this document
The Japanese version of this document is formal specification. A customer may use this translation version only for a reference
to help reading the formal version.
If there are any differences in translation version of this document formal version takes priority.
Figure 54. Unused circuit example
VCC
VEE
+
-
Please keep this
potential in Vicm
相關PDF資料 |
PDF描述 |
|---|---|
| 0071.3041.T2 | VARISTOR 300V 10MM RADIAL |
| 0071.2741.T2 | VARISTOR 270V 10MM RADIAL |
| BA3472F-E2 | IC OPAMP DUAL 36V 4MA SOP-8 |
| 61900419521 | HEADER 4POS PIN R/A 2.54MM T/H |
| 0071.2541.T2 | VARISTOR 250V 10MM RADIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BA3472FVJE2 | 制造商:ROHM 制造商全稱:Rohm 功能描述:High Speed with High Voltage Operational Amplifiers |
| BA3472FVJTR | 制造商:ROHM 制造商全稱:Rohm 功能描述:High Speed with High Voltage Operational Amplifiers |
| BA3472FVM | 制造商:ROHM 制造商全稱:Rohm 功能描述:Operational Amplifiers: High Speed |
| BA3472FVME2 | 制造商:ROHM 制造商全稱:Rohm 功能描述:High Speed with High Voltage Operational Amplifiers |
| BA3472FVMTR | 制造商:ROHM 制造商全稱:Rohm 功能描述:High Speed with High Voltage Operational Amplifiers |
發布緊急采購，3分鐘左右您將得到回復。