- 您現在的位置：買賣IC網 > PDF目錄369404 > BA683A LED Display Driver PDF資料下載
參數資料
| 型號： | BA683A |
| 英文描述： | LED Display Driver |
| 中文描述： | LED顯示驅動器 |
| 文件頁數： | 4/5頁 |
| 文件大?。?/td> | 91K |
| 代理商： | BA683A |
654
Audio ICs
BA683A
Attached components
(1)
LED current setting resistor (R
1
)
This resistor sets the LED current value. Refer to Fig. 3
for the relationship between the value of this resistor and
the current value. The ratio of the current for outputs 1 to
8 and 9 to 12 is about 2: 1. The recommended value is
for this resistor is 27k
. If the LED current is set too high,
the allowable power dissipation of the package may be
exceeded, so exercise due caution.
(2)
Input coupling capacitor (C
1
)
This capacitor connects the BA683A to external input cir-
cuits. The recommended value is 2.2
μ
F.
(3)
Input bias resistor (R
2
)
This resistor is the input impedance. If the value is set too
large, the DC bias voltage will increase, and the input off-
set will increase and have an effect on the comparators.
The recommended value is 10k
.
(4)
Resistor and capacitor that set the LED operation
level discharge time constant (R
3
and C
2
)
These components set the discharge time constant for
LED operation level. The recommended values are R
3
=
10k
and C
2
= 10
μ
F.
(5)
These resistors are used to adjust the input offset for the
rectifier amplifier. The recommended values are R
4
=
240k
, and VR
1
= 500
. If the value of VR
1
is too high,
adjustment becomes difficult, and if it is too small, adjust-
ment may not be possible.
(6)
Power supply capacitor (C
3
)
This capacitor stabilizes the power supply line. The rec-
ommended value is 10
μ
F. This capacitor will have no ef-
fect if its value is 1
μ
F or less.
Input offset adjustment resistors (R
4
and VR
1
)
Operation notes
(1)
LED connection
Connect the LEDs as indicated in Fig. 2 (1) and Fig 2 (2).
Note that the connection methods are different for bar
and dot displays, and that in the case of bar display, pin
18 is open, while for dot display, pin 18 is connected to
GND.
For the BA683A, the ratio of the current for LEDs L
1
to L
8
and L
9
to L
12
is about 2: 1. If you want the current ratio for
some of the L1 to L8 LEDs to be 1, reduce the current by
connecting a resistance in parallel with the LED. Short
any LED that are unused. Connect the LEDs that are not
used from the lowest level LED (except when the 12th
LED is not used for display alignment).
(2)
LED current adjustment
The LED current is set using R
1
. The relationship be-
tween the value of R
1
and the typical LED current is given
in Fig. 3.
(3)
In the case of the BA683A, the comparator voltage is the
input voltage when about half LED current setting value
(Typ.) starts flowing in an LED.
Therefore, if the LED current is set to 16mA, when the
third LED starts to light and 8mA is flowing in the LED,
this input voltage is the third comparator voltage.
(4)
0dB and input offset adjustment
First, adjust the input signal so that the 10th LED lights.
This is the 0dB input signal level. Next, lower the input
signal level to
27dB, and adjust the offset adjustment
potentiometer VR
1
so that the first LED lights. Repeat the
0dB and
27dB adjustments alternately to accurately
set the levels. The input level at which an LED lights is the
comparator voltage.
(5)
Earthing
The BA683A GND (pin 9) and the external component
earths should connected together at one point.
Comparator voltage
相關PDF資料 |
PDF描述 |
|---|---|
| BA683 | Band-switching diodes |
| BA683 | 1.02M, 1206, 1/4W, 1% |
| BA6840AFS | Industrial Control IC |
| BA6842BFP | 光ディスクLSI |
| BA684A | Capacitor: Capacitance [nom]: 1uF; Working Voltage (Vdc)[max]: 50Vdc / 30VAC; Capacitance Tolerance: +/-10%; Dielectric: Metallized Polyethylene Naphthalate (PEN); Temperature Range: -55°C to +125°C; Lead Style: Surface Mount Chip; Body Dimensions: 10.2mm x 9.1mm x 5.5mm; Container: Tape & Reel |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BA683-GS08 | 功能描述:PIN 二極管 100 mA 35 Volt Band RoHS:否 制造商:Skyworks Solutions, Inc. 配置: 反向電壓:200 V 正向連續電流: 頻率范圍:10 MHz to 6 GHz 端接類型:SMD/SMT 封裝 / 箱體:QFN-3 封裝:Reel |
| BA683-GS18 | 功能描述:PIN 二極管 35 Volt 100mA Band RoHS:否 制造商:Skyworks Solutions, Inc. 配置: 反向電壓:200 V 正向連續電流: 頻率范圍:10 MHz to 6 GHz 端接類型:SMD/SMT 封裝 / 箱體:QFN-3 封裝:Reel |
| BA683-M-08 | 功能描述:RF Diode SOD-80 MiniMELF 制造商:vishay semiconductor diodes division 系列:- 包裝:帶卷（TR） 零件狀態:過期 二極管類型:- 電壓 - 峰值反向（最大值）:- 電流 - 最大值:- 不同?Vr，F(xiàn) 時的電容:- 不同?If，F(xiàn) 時的電阻:- 功率耗散（最大值）:- 封裝/外殼:DO-213AC, MINI-MELF, SOD-80 供應商器件封裝:SOD-80 MiniMELF 標準包裝:2,500 |
| BA683-M-18 | 功能描述:RF Diode SOD-80 MiniMELF 制造商:vishay semiconductor diodes division 系列:- 包裝:帶卷（TR） 零件狀態:過期 二極管類型:- 電壓 - 峰值反向（最大值）:- 電流 - 最大值:- 不同?Vr，F(xiàn) 時的電容:- 不同?If，F(xiàn) 時的電阻:- 功率耗散（最大值）:- 封裝/外殼:DO-213AC, MINI-MELF, SOD-80 供應商器件封裝:SOD-80 MiniMELF 標準包裝:10,000 |
| BA6840 | 制造商:ROHM 制造商全稱:Rohm 功能描述:3-phase motor driver |
發布緊急采購，3分鐘左右您將得到回復。