- 您現在的位置：買賣IC網 > PDF目錄295138 > BA7810CP-E2 10 V FIXED POSITIVE REGULATOR, SFM3 PDF資料下載
參數資料
| 型號： | BA7810CP-E2 |
| 元件分類： | 固定正電壓單路輸出標準穩壓器 |
| 英文描述： | 10 V FIXED POSITIVE REGULATOR, SFM3 |
| 封裝： | ROHS COMPLIANT, TO-220, 3 PIN |
| 文件頁數： | 2/13頁 |
| 文件大?。?/td> | 581K |
| 代理商： | BA7810CP-E2 |
10/12
●
Thermal design
Refer to the following thermal derating curves (Fig. 25, 26), when using in the status of Ta=25℃ or more.
The characteristic of IC is greatly related to the operating temperature.
When it is used in over maximum junction temperature, the elements inside IC might become weaker and be destroyed.
It is recommended to take into consideration thermal of IC.
Note that the temperatures are in the allowed temperature limits and operated within Pd.
It is necessary to operate it at junction temperature Tjmax or less to prevent IC from the thermal destruction.
Please operate IC within permissible loss Pd because the junction temperature Tj might become considerably a high
temperature even if ambient temperature Ta is normal temperature (25℃).
Power consumption Pc(W) may be expressed by the equation shown below:
Pc=(Vin-Vo)×Io+ Vin×Iｂ
permissible loss Pd≧Pc
Maximum Output current IoMAX can be calculated in thermal design.
·
Calculation example
Ex.1) Ta=85℃, Vin =7.5V, Vo=5.0V
Io≦400ｍA
Be sure to use this IC within a power dissipation at the range of operating temperature.
Fig.25 Thermal derating curve (TO220CP-3)
Fig.26 Thermal derating curve (TO252-3)
●
Terminal Setting and Cautions
·
INPUT
It is recommended that a capacitor (about 0.33uF) be inserted between INPUT and COMMON.
The value of capacitor is designed suitable for the actual application.
·
OUTPUT
It is recommended that a capacitor (about 0.1uF) be inserted between OUTPUT and COMMON.
A tantalum capacitor can also be used for this pin because insufficient capacitors may cause oscillation by a temperature
change.
·
COMMON
Keep the no voltage drop between Ground level of set board and IC.
When there is the voltage difference, setting voltage becomes inaccuracy and unstable.
It is recommended to connect by wide, short pattern, and lower the inpedance.
Vo
Vin
Ib
Vin
Pd
Io
≦
5.0
7.5
4.5m
7.5
1.04
Io
≦
Vin : Input Voltage
Vo : Output Voltage
Io
: Output Current
Ib
: Bias current
Using TO220CP-3 alone
θ
ja=62.5℃/W→16mW/℃
Pd=1.04W at 85℃
12.5
10
7.5
5
2.5
0
25
50
75
125
100
150
AMBIENT TEMPERATURE : Ta[℃]
POWER
D
ISSI
P
A
T
ION:
Pd[
W
]
(2) 1.0
(1) 10.0
(1) Mounted on infinity Alminium heat sinkθj-c=12.5 (℃/W)
(2) Using an IC aloneθj-a=125.0℃/W
25
20
15
10
5
0
25
50
75
125
100
150
AMBIENT TEMPERATURE : Ta[℃]
POWER
D
ISSI
P
A
T
ION:
Pd[
W
]
(2) 2.0
(1) 22.0 (1) Mounted on infinity Alminium heat sinkθj-c=5.7(℃/W)
(2) Using an IC aloneθj-a=62.5℃/W
相關PDF資料 |
PDF描述 |
|---|---|
| BA78M10CP-E2 | 10 V FIXED POSITIVE REGULATOR, SFM3 |
| BA78M10FP-E2 | 10 V FIXED POSITIVE REGULATOR, PSSO2 |
| BAPL | FEMALE, TELECOM AND DATACOM CONNECTOR, SOLDER |
| BAP | MALE, TELECOM AND DATACOM CONNECTOR, SOLDER |
| BAV21.TR | 0.2 A, 200 V, SILICON, SIGNAL DIODE, DO-35 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BA7810FP-E2 | 功能描述:線性穩壓器 - 標準 STANDARD REG POS 10V 1A RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| BA7812 | 制造商:ROHM 制造商全稱:Rohm 功能描述:1A Output 78 series Regulators 500mA Output 78 series Regulators |
| BA7812CP-E2 | 功能描述:線性穩壓器 - 標準 IC REG 14.5-27 VOUT 12V 1A RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| BA7812FP-E2 | 功能描述:線性穩壓器 - 標準 STANDARD REG POS 12V 1A RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| BA7815 | 制造商:ROHM 制造商全稱:Rohm 功能描述:1A Output 78 series Regulators 500mA Output 78 series Regulators |
發布緊急采購，3分鐘左右您將得到回復。