- 您現在的位置：買賣IC網 > PDF目錄295138 > BA78M08CP 8 V FIXED POSITIVE REGULATOR, SFM3 PDF資料下載
參數資料
| 型號： | BA78M08CP |
| 元件分類： | 固定正電壓?jiǎn)温份敵鰳?biāo)準穩壓器 |
| 英文描述： | 8 V FIXED POSITIVE REGULATOR, SFM3 |
| 封裝： | ROHS COMPLIANT, TO-220, 3 PIN |
| 文件頁數： | 3/13頁 |
| 文件大?。?/td> | 581K |
| 代理商： | BA78M08CP |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
11/12
●
Note For Use
(1) Absolute Maximum Ratings
While utmost care is taken to quality control of this product, any application that may exceed some of the absolute
maximum ratings including the voltage applied and the operating temperature range may result in breakage. If broken,
short-mode or open-mode may not be identified. So if it is expected to encounter with special mode that may exceed the
absolute maximum ratings, it is requested to take necessary safety measures physically including insertion of fuses.
(2) Ground voltage
Make setting of the potential of the GND terminal so that it will be maintained at the minimum in any operating state.
Furthermore, check to be sure no terminals are at a potential lower than the GND voltage including an actual electric
transient.
(3) Thermal design
When you do the kind of use which exceeds Pd, It may be happened to deteriorating IC original quality such as
decrease of electric current ability with chip temperature rise. Do not exceed the power dissipation (Pd) of the package
specification rating under actual operation, and please design enough temperature margins.
(4) Short-circuiting between terminals, and mismounting
When mounting to pc board, care must be taken to avoid mistake in its orientation and alignment. Failure to do so
may result in IC breakdown. Short-circuiting due to foreign matters entered between output terminals, or between
output and power supply or GND may also cause breakdown.
(5) Operation in Strong electromagnetic field
Be noted that using the IC in the strong electromagnetic radiation can cause operation failures.
(6) Inspection with the IC set to a pc board
If a capacitor must be connected to the pin of lower impedance during inspection with the IC set to a pc board, the
capacitor must be discharged after each process to avoid stress to the IC. For electrostatic protection, provide proper
grounding to assembling processes with special care taken in handling and storage. When connecting to jigs in the
inspection process, be sure to turn OFF the power supply before it is connected and removed.
(7) Input to IC terminals
This is a monolithic IC with P
+ isolation between P-substrate and each element as illustrated below. This P-layer and
the N-layer of each element form a P-N junction, and various parasitic element are formed.
If a resistor is joined to a transistor terminal as shown in Fig 28.
○
P-N junction works as a parasitic diode if the following relationship is satisfied; GND>Terminal A (at resistor side), or
GND>Terminal B (at transistor side); and
○
if GND>Terminal B (at NPN transistor side),
a parasitic NPN transistor is activated by N-layer of other element adjacent to the above-mentioned parasitic diode.
The structure of the IC inevitably forms parasitic elements, the activation of which may cause interference among
circuits, and/or malfunctions contributing to breakdown. It is therefore requested to take care not to use the device in
such manner that the voltage lower than GND (at P-substrate) may be applied to the input terminal, which may result in
activation of parasitic elements.
(8) Ground wiring pattern
If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND
pattern from the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that
resistance to the wiring pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of the
small-signal GND. Pay attention not to cause fluctuations in the GND wiring pattern of external parts as well.
(9) Thermal shutdown circuit
A temperature control circuit is built in the IC to prevent the damage due to overheat.
Therefore, the output is turned off when the thermal circuit works and is turned on when the temperature goes down to
the specified level.
But, built-in the IC a temperature control circuit to protect itself, and avoid the design used the thermal protection.
(10) Over current protection circuit
The over-current protection circuits are built in at output, according to their respective current outputs and prevent the
IC from being damaged when the load is short-circuited or over-current. But, these protection circuits are effective for
preventing destruction by unexpected accident. When it’s in continuous protection circuit moving period don’t use please.
And for ability, because this chip has minus characteristic, be careful for heat plan.
(11) There is a possibility to damage an internal circuit or the element when Vin and the voltage of each terminal reverse in the
application.
For instance, Vin is short-circuited to GND etc. with the charge charged to an external capacitor. Please use the
capacitor of the output terminal with 1000μF or less. Moreover, the Vin series is recommended to insert the diode of the
by-pass the diode of the backflow prevention or between each terminal and Vin.
Fig.27 Bypass Diode
Fig.28
Simplified structure of monorisic IC
VCC
Output terminal
Bypass diode
Backflow prevention diode
P substrate
Pin A
Parasitic
element
Resistor
N
P
+
P
+
P
GND
Parasitic element
Pin A
P substrate
Transistor (NPN)
N
P
+
P
+
P
GND
Parasitic element
Pin B
C
B
E
N
GND
Pin B
Other adjacent elements
E
B
C
GND
Parasitic
element
相關PDF資料 |
PDF描述 |
|---|---|
| BA78M08FP | 8 V FIXED POSITIVE REGULATOR, PSSO2 |
| BA78M08CP-E2 | 8 V FIXED POSITIVE REGULATOR, SFM3 |
| BA78M08FP-E2 | 8 V FIXED POSITIVE REGULATOR, PSSO2 |
| BA7810CP-E2 | 10 V FIXED POSITIVE REGULATOR, SFM3 |
| BA78M10CP-E2 | 10 V FIXED POSITIVE REGULATOR, SFM3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BA78M08CPE2 | 制造商:ROHM 制造商全稱:Rohm 功能描述:1A Output 78 series Regulators 500mA Output 78 series Regulators |
| BA78M08CP-E2 | 功能描述:線性穩壓器 - 標準 IC REG 10.5-23 VOUT 8V 500MA RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
| BA78M08FP | 制造商:ROHM 制造商全稱:Rohm 功能描述:Three-Terminal Regulator |
| BA78M08FPE2 | 制造商:ROHM 制造商全稱:Rohm 功能描述:1A Output 78 series Regulators 500mA Output 78 series Regulators |
| BA78M08FP-E2 | 功能描述:線性穩壓器 - 標準 IC REG 10.5-23 VOUT 8V 500MA RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L |
發布緊急采購，3分鐘左右您將得到回復。