- 您現在的位置：買賣IC網 > PDF目錄295161 > BMP-5/4-Q48 2-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | BMP-5/4-Q48 |
| 元件分類： | 電源模塊 |
| 英文描述： | 2-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
| 文件頁數： | 6/6頁 |
| 文件大小： | 104K |
| 代理商： | BMP-5/4-Q48 |
25-40W ,
DU AL
OUTPUT
DC/DC
CONVER TERS
XMP Series
66
On/Off Control (Standard)
The On/Off Control pin (pin 5) may be used for remote on/off operation. As
shown in Figure 6, the control pin has an internal 10k
pull-up resistor to
approximately 10V. The converter is designed so that it is enabled when the
control pin is left open (normal mode) and disabled when the control pin is
pulled low (to less than +0.8V relative to –Input, pin 2).
Dynamic control of the on/off function is best accomplished with a mechani-
cal relay or an open-collector/open-drain drive circuit (optically isolated if
appropriate). The drive circuit should obviously be able to sink approximately
1mA when activated and withstand more than 10 Volts when deactivated.
Applying an external voltage to pin 5 when no input power is applied to the
converter can cause permanent damage to the converter. The on/off control
function, however, is designed such that the converter can be disabled (pin 5
pulled low) while input power is ramping up and then "released" once the
input has stabilized. Under these circumstances, it takes approximately
30ms for the output of the fully loaded DC/DC to ramp up and settle to within
±1% of its final value after the converter has been turned on.
Synchronization (Optional)
In critical applications employing multiple switching DC/DC converters, it may
be desirable to intentionally synchronize the switching of selected converters
(so the system noise can be reduced with notch filtering) or to purposely
desynchronize the converters (to lessen the current-carrying requirements on
intermediate dc buses). BMP DC/DC Converters have been designed so that
the On/Off Control function on pin 5 can be replaced with a Sync function. This
change has to be implemented by DATEL during the product assembly
process. Contact our Applications Engineering Group for additional details.
To synchronize the switching of multiple BMP converters configured with the
Sync function, an external clock can be applied to pin 5 of each converter.
The clock should be a TTL square wave referenced to –Input (logic high =
+2 to +5 Volts, 250A max.; logic low = 0 to +0.8 Volts, 70A max.) with a
maximum 1sec "high" duration. The frequency of the synchronizing clock
should be higher than that of any individual converter. Therefore, it should be
145kHz ±5kHz.
Output Trimming
The total output voltage span, from +Output (pin 9) to –Output (pin 6) may
be trimmed ±5% via a single trimpot or fixed resistor. The trimpot should be
connected as shown in Figure 8 with its wiper connected to pin 10 (Trim). A
trimpot can also be used to determine the value of a single fixed resistor
which can be connected between pin 10 (Trim) and pin 9 (+Output) to trim
"down" the output voltages, or between pins 10 (Trim) and 6 (–Output) to
trim "up" the output voltages. Fixed resistors should be metal-film types with
absolute TCR's less than 100ppm/°C to ensure stability.
Figure 7. Using External Capacitors
to Reduce Input/Output Ripple/Noise
Figure 8. Trim Connections Using a Trimpot
DS-0411
11/01
–OUTPUT
+INPUT
–INPUT
+OUTPUT
3
2
9
6
COMMON
8
CIN
COUT
+
20k
9
5-10
Turns
+INPUT
–INPUT
TRIM
COMMON
3
2
9
6
8
LOAD
10
–OUTPUT
+OUTPUT
Case Connection
Unlike most other DC/DC converters, BMP DC/DC's do not have their metal
case connected to one of their input pins. The "uncommitted" case is
connected to pin 4 which, depending on your system configuration, should be
connected to either +Input (pin 3) or –Input (pin 2).
+INPUT
–INPUT
3
2
+10V
10k
9
5
ON/OFF
CONTROL
Figure 6. Driving the On/Off Control Pin
DATEL makes no representation that the use of its products in the circuits described herein, or the use of other technical information contained herein, will not infringe upon existing or future patent rights. The descriptions
contained herein do not imply the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without notice. The DATEL logo is a registered DATEL,
Inc. trademark.
DATEL (UK) LTD. Tadley, England Tel: (01256)-880444
DATEL S.A.R.L. Montigny Le Bretonneux, France Tel: 01-34-60-01-01
DATEL GmbH München, Germany Tel: 89-544334-0
DATEL KK Tokyo, Japan Tel: 3-3779-1031, Osaka Tel: 6-6354-2025
DATEL, Inc. 11 Cabot Boulevard, Mansfield, MA 02048-1151
Tel: (508) 339-3000
(800) 233-2765
Fax: (508) 339-6356
Internet: www.datel.com
Email: sales@datel.com
Data Sheet Fax Back: (508) 261-2857
INNOVATION and EXCELLENCE
ISO-9001 REGISTERED
相關PDF資料 |
PDF描述 |
|---|---|
| BMR4532101/000 | DC-DC REG PWR SUPPLY MODULE |
| BNC-22 | CABLE TERMINATED, MALE, BNC CONNECTOR, CRIMP, PLUG |
| BNC-BHJ-13 | PANEL MOUNT, CABLE TERMINATED, FEMALE, BNC CONNECTOR, CRIMP, JACK |
| BP5081B15 | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| BPR-105 | POSITION, LINEAR SENSOR-DIFFUSE, 1-1mm, RECTANGULAR, THROUGH HOLE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BMP71 | 制造商:Brady Corporation 功能描述:13.100x9.500x4.600 LABEL PRINTER 制造商:Brady Corporation 功能描述:LABEL PRINTER, THERMAL TRANSFER; Color:Blue; External Depth:332.7mm; External Height:116.8mm; External Width:241.3mm; For Use With:Brady BM71 tapes; self laminating & die cut labels, printer ribbons; heat shrink sleeves 制造商:Brady Corporation 功能描述:BMP71 LABEL PRINTER |
| BMP71-360 | 制造商:Brady Corporation 功能描述:BMP71 360 REPLACEMENT PRINTER PROGRAM |
| BMP71-360-KIT | 制造商:Brady Corporation 功能描述:BMP71 PRINTER AND 360 WARRANTY |
| BMP71-DEMO | 制造商:Brady Identification 功能描述:BRADY BMP71 DEMO 115157 |
| BMP71-LM | 制造商:Brady Corporation 功能描述:BMP Series Printer with LabelMark Software |
發布緊急采購，3分鐘左右您將得到回復。