- 您現在的位置：買賣IC網 > PDF目錄166512 > BU-61582G3-490 (DATA DEVICE CORP) 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CDSO70 PDF資料下載
參數資料
| 型號： | BU-61582G3-490 |
| 廠商： | DATA DEVICE CORP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CDSO70 |
| 封裝： | CERAMIC, GULL LEAD, 70 PIN |
| 文件頁數： | 10/48頁 |
| 文件大?。?/td> | 378K |
| 代理商： | BU-61582G3-490 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
18
Data Device Corporation
www.ddc-web.com
BU-61582
G-08/02-250
CIRCULAR BUFFER MODE
FIGURE 6 illustrates the RT circular buffer memory management
scheme. The circular buffer mode facilitates bulk data transfers.
The size of the RT circular buffer, shown on the right side of the
figure, is programmable from 128 to 8192 words (in even powers
of 2) by the respective Subaddress Control Word. As in the sin-
gle message mode, the host processor initially loads the individ-
ual Lookup Table entries. At the start of each message, the
SP’ACE stores the Lookup Table entry in the third position of the
respective message block descriptor in the stack area of RAM,
as in the Single Message mode. The SP’ACE transfers Receive
or Transmit Data Words to (from) the circular buffer, starting at
the location referenced by the Lookup Table pointer.
At the end of a valid (or, optionally, invalid) message, the value of
the Lookup Table entry updates to the next location after the last
address accessed for the current message. As a result, Data
Words for the next message directed to the same Tx/RX(/Bcst)
subaddress will be accessed from the next contiguous block of
address locations within the circular buffer. As a recommended
option, the Lookup Table pointers may be programmed to not
update following an invalid receive (or broadcast) message. This
allows the 1553 bus controller to retry the failed message, result-
ing in the valid (retried) data overwriting the invalid data. This
eliminates overhead for the RT’s host processor. When the
pointer reaches the lower boundary of the circular buffer (locat-
ed at 128, 256, . . . 8192-word boundaries in the BU-61582
address space), the pointer moves to the top boundary of the cir-
cular buffer, as FIGURE 6 shows.
IMPLEMENTING BULK DATA TRANSFERS
The use of the Circular Buffer scheme is ideal for bulk data trans-
fers; that is, multiple messages to/from the same subaddress.
The recommendation for such applications is to enable the cir-
cular buffer interrupt request. By so doing, the routine transfer of
multiple messages to the selected subaddress, including errors
and retries, is transparent to the RT’s host processor. By strate-
gically initializing the subaddress’s Lookup Table pointer prior to
the start of the bulk transfer, the BU-61582 may be configured to
issue an interrupt request only after it has received the anticipat-
ed number of valid Data Words to the designated subaddress.
SUBADDRESS DOUBLE BUFFERING MODE
For receive (and broadcast) subaddresses, the BU-61582 RT
offers a third memory management option, Subaddress Double
Buffering. Subaddress double buffering provides a means of
ensuring data consistency. FIGURE 7 illustrates the RT
Subaddress Double Buffering scheme. Like the Single Message
and Circular Buffer modes, the Double Buffering mode may be
selected on a subaddress basis by means of the Subaddress
Control Word. The purpose of the Double Buffering mode is to
provide the host processor a convenient means of accessing the
most recent, valid data received to a given subaddress. This
serves to ensure the highest possible degree of data consisten-
cy by allocating two 32-bit Data Word blocks for each individual
receive (and/or broadcast) subaddress.
At a given point in time, one of the two blocks will be designated
as the “active” 1553 data block while the other will be designat-
ed as the “inactive” block. The Data Words from the next receive
message to that subaddress will be stored in the “active” block.
15
13
0
RECEIVED
(TRANSMITTED)
MESSAGE
DATA
(NEXT LOCATION)
POINTER TO
CURRENT
DATA BLOCK
POINTER TO
NEXT DATA
BLOCK
LOOK-UP TABLE
ENTRY
LOOK-UP TABLES
LOOK-UP
TABLE
ADDRESS
BLOCK STATUS WORD
TIME TAG WORD
DATA BLOCK POINTER
RECEIVED COMMAND
WORD
CONFIGURATION
REGISTER #1
STACK
POINTERS
DESCRIPTOR
STACK
CURRENT
AREA B/A
1. TX/RX/BCST_SA look-up table entry is updated following valid receive (broadcast) message
or following completion of transit message
Notes:
*
50%
CIRCULAR
BUFFER
ROLLOVER
INTERRUPT
100%
CIRCULAR
BUFFER
ROLLOVER
INTERRUPT
CIRCULAR
DATA BUFFER*
(128,256,...8192 WORDS)
FIGURE 6. RT MEMORY MANAGEMENT: CIRCULAR BUFFER MODE
相關PDF資料 |
PDF描述 |
|---|---|
| BU-61582G3-491L | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CDSO70 |
| BU-61582G3-491S | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CDSO70 |
| BU-61582G3-491Z | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CDSO70 |
| BU-61582G3-500K | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CDSO70 |
| BU-61582G3-501K | 2 CHANNEL(S), 1M bps, MIL-STD-1553 CONTROLLER, CDSO70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BU-61585 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MIL-STD-1553 Components |ACE |
| BU-61586 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MIL-STD-1553 Components |ACE |
| BU61586V6-300 | 制造商:DDC 功能描述:MIL-STD-1553/ARINC BUS CONTROLLER/RTU, 70 Pin, Flat Pack |
| BU-61588 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MINIATURE ADVANCED COMMUNICATION ENGINE (MINI-ACE) AND MINI-ACE PLUS |
| BU-61588F0 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MINIATURE ADVANCED COMMUNICATION ENGINE (MINI-ACE) AND MINI-ACE PLUS |
發布緊急采購，3分鐘左右您將得到回復。