- 您現在的位置：買賣IC網 > PDF目錄223464 > BUF01900AIDRCR (TEXAS INSTRUMENTS INC) SPECIALTY ANALOG CIRCUIT, PDSO10 PDF資料下載
參數資料
| 型號： | BUF01900AIDRCR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| 封裝： | 3 X 3 MM, 0.90 MM HEIGHT, GREEN, PLASTIC, SON-10 |
| 文件頁數： | 3/26頁 |
| 文件大小： | 662K |
| 代理商： | BUF01900AIDRCR |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
BUF01900
BUF01901
SBOS337A OCTOBER 2006 REVISED OCTOBER 2006
www.ti.com
11
ACQUIRE OF OTP MEMORY
An acquire command updates the DAC output to the value
stored in OTP memory. If the OTP memory has not been
programmed, the DAC output code is ‘0000000000’.
Figure 19 shows the timing diagram for the acquire
command.
Acquire Command
1.
Send a START condition on the bus.
2.
Send the device address and read/write bit = LOW.
The device will acknowledge this byte.
3.
Send the acquire command. Bits D7—D5 must be
set to 001. Bits D4—D0 do not have meaning. This
byte will be acknowledged.
4.
Send a STOP condition on the bus.
Writing OTP Memory
The BUF0190x is able to write to the OTP memory a maxi-
mum of four times. Writing to the OTP memory a fourth
time uses all available memory and disables the ability to
perform additional writes (see table 3). A reset or acquire
command updates the DAC output to the most recently
written OTP memory value.
When programming the OTP memory, the analog supply
voltage must be between 8.5V and 18V.
Write commands are performed by setting the read/write
bit LOW.
To write to OTP memory:
1.
Send a START condition on the bus.
2.
Send the device address and read/write bit = LOW.
The BUF0190x acknowledges this byte.
3.
Send two bytes of data for the OTP memory. Begin by
sending the most significant byte first (bits D15
—D8,
of which only bits D9 and D8 are data bits, and bits
D15
—D13 must be 010), followed by the least
significant byte (bits D7
—D0). The register updates
after receiving the second byte.
4.
Send a STOP condition on the bus.
The BUF0190x acknowledges each data byte. If the mas-
ter terminates communication early by sending a STOP or
START condition on the bus, the specified OTP register
will not be updated. Writing an OTP register updates the
DAC output voltage.
Programming timing is taken from the two-wire bus.
Therefore, the master must provide correct timing on the
bus to ensure data is successfully written into OTP
memory. Figure 20 shows the timing requirements for tim-
ing when the OTP write supply and OTP write signal are
active.
相關PDF資料 |
PDF描述 |
|---|---|
| BUF08821AIPWPR | VIDEO CLOCK GENERATOR, PDSO20 |
| BUK657-600B | N-Channel Enhancement MOSFET |
| BUK657-600C | N-Channel Enhancement MOSFET |
| BUK7105-40ATE | TrenchPLUS standard level FET |
| BUK7107-40ATC | TrenchPLUS standard level FET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BUF01900AIDRCRG4 | 功能描述:LCD Gamma緩沖器 Ref Vltg Gen for VCOM Adj RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| BUF01900AIDRCT | 功能描述:LCD Gamma緩沖器 Ref Vltg Gen for VCOM Adj RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| BUF01900AIDRCTG4 | 功能描述:LCD Gamma緩沖器 Ref Vltg Gen for VCOM Adj RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| BUF01900AIPW | 功能描述:LCD Gamma緩沖器 Ref Vltg Gen for VCOM Adj RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| BUF01900AIPWG4 | 功能描述:LCD Gamma緩沖器 Ref Vltg Gen for VCOM Adj RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。