- 您現在的位置：買賣IC網 > PDF目錄166722 > BUS-65145-250Y PROGRAMMABLE QUAD BIPOLAR OPERATIONAL AMPLIFIERS PDF資料下載
參數資料
| 型號： | BUS-65145-250Y |
| 元件分類： | 運算放大器 |
| 英文描述： | PROGRAMMABLE QUAD BIPOLAR OPERATIONAL AMPLIFIERS |
| 中文描述： | MIL-STD-1553/ARINC總線控制器/ RTU通訊 |
| 文件頁數： | 6/24頁 |
| 文件大?。?/td> | 219K |
| 代理商： | BUS-65145-250Y |
14
the appropriate I/O signals. Mode command illegalization and
handling are detailed below in TABLE 2.
MODE CODES
The BUS-65142 implements all mode codes applicable to dual-
redundant systems. Mode codes can also be illegalized using
TABLE 2. MODE CODES IMPLEMENTED
DYNAMIC BUS CONTROL (00000)
MESSAGE SEQUENCE = DBC * STATUS
The RT responds with status. If the subsystem wants control of the bus, it must set DBACC in the Configuration Register.
ERROR CONDITIONS
1. Invalid Command. No response, command ignored.
2. Command Followed by Data Word. No status response. Bits Set: message error (SW), High Word Count (BIT Word).
3.
bit Set to Zero. No status response. Bits set: message error (S/W), T/R Error (BIT Word).
4. Zero
bit and Broadcast Address. No status response. Bits Set: message error, broadcast received (S/W), Illegal Mode Code,
T/R Error (BIT Word).
5. Broadcast Address. No status response. Bits Set: message error, broadcast received (S/W), Illegal Mode Code (BIT Word).
R
T/
R
T/
SYNCHRONIZE WITHOUT DATA WORD (00001)
MESSAGE SEQUENCE = SYNC * STATUS
The RT responds with status. If sent as a broadcast, the broadcast receive bit will be set and status response suppressed.
ERROR CONDITIONS
1. Invalid Command. No response, command ignored.
2. Command Followed by Data Word. No statue response. Bits Set: message error (SW), High Word Count (BIT Word)
3.
bit Set to Zero. No statue response. Bits set: message error (S/W), T/R Error (BIT Word).
4. Zero
bit and Broadcast Address. No statue response. Bits Set: message error, broadcast received (S/W), Illegal Mode Code,
T/R Error (BIT Word).
R
T/
R
T/
STATUS WORD (00010)
MESSAGE SEQUENCE = TRANSMIT WORD * STATUS
The status and BIT word registers are not altered by this command and contain the status from the previous command.
ERROR CONDITIONS
1. Invalid Command. No response, command ignored.
2. Command Followed by Data Word. No statue response. Bits Set: message error (SW), High Word Count (BIT Word)
3.
bit Set to Zero. No statue response. Bits set: message error (S/W), T/R Error (BIT Word).
4. Zero
bit and Broadcast Address. No statue response. Bits Set: message error, broadcast received (S/W), Illegal Mode Code,
T/R Error (BIT Word).
5. Broadcast Address. No statue response. Bits Set: message error, broadcast received (S/W), T/R Error (BIT Word).
R
T/
R
T/
INITIATE SELF-TEST (00011)
MESSAGE SEQUENCE = SELF TEST * STATUS
The RT responds with a status word. If the command was broadcast, the broadcast received bit is set and status transmission suppressed.
Short-loop test is initiated on the status word transmitted. If the test fails, an RT fail flag is set.
ERROR CONDITIONS
1. Invalid Command. No response, command ignored.
2. Command Followed by Data Word. No statue response. Bits Set: message error (SW), High Word Count (BIT Word)
3.
bit Set to Zero. No statue response. Bits set: message error (S/W), T/R Error (BIT Word).
4. Zero
bit and Broadcast Address. No statue response. Bits Set: message error, broadcast received (S/W), T/R Error (BIT Word).
5. Faulty Test. Bits set: terminal flag (S/W),
Loop Test Fail, Current 1553 Bus (A or B) Loop Test Fail (BIT Word)
B
/
A
R
T/
R
T/
TRANSMITTER SHUTDOWN (00100)
MESSAGE SEQUENCE =SHUTDOWN * STATUS
This command is only used with dual redundant bus systems. The RT responds with status. At the end of the status transmission, the RT inhibits
any further transmission from the dual redundant channel. Once shutdown, the transmitter can only be reactivated by OVERRIDE TRANSMITTER
SHUTDOWN or RESET RT commands.
ERROR CONDITIONS
1. Invalid Command. No response, command ignored.
2. Command Followed by Data Word. No statue response. Bits Set: message error (SW), High Word Count (BIT Word)
3.
bit Set to Zero. No statue response. Bits set: message error (S/W), T/R Error (BIT Word).
4. Zero
bit and Broadcast Address. No statue response. Bits Set: message error, broadcast received (S/W), Illegal Mode Code,
T/R Error (BIT Word).
R
T/
R
T/
* = Status Response Time
相關PDF資料 |
PDF描述 |
|---|---|
| BUS-65145-250Z | PROGRAMMABLE QUAD BIPOLAR OPERATIONAL AMPLIFIERS |
| BUS-65145-260 | Low power quad operational amplifier |
| BUS-65145-260K | Low power quad operational amplifier |
| BUS-65145-260L | Low power quad operational amplifier |
| BUS-65145-260Q | Low power quad operational amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| BU-S802 | 制造商:Fuji Electric 功能描述: |
| BU-S803 | 制造商:Fuji Electric 功能描述: |
| BUS98 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SITCHMODE Series NPN Silicon Power Transistors |
| BUS98/D | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SWITCHMODE? Series NPN Silicon Power Transistors |
| BUS98A | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:SITCHMODE Series NPN Silicon Power Transistors |
發布緊急采購，3分鐘左右您將得到回復。