參數資料
型號: C8051F304-GMR
廠商: Silicon Laboratories Inc
文件頁數: 4/178頁
文件大小: 0K
描述: IC 8051 MCU 4K FLASH 11QFN
產品培訓模塊: Serial Communication Overview
標準包裝: 1,500
系列: C8051F30x
核心處理器: 8051
芯體尺寸: 8-位
速度: 25MHz
連通性: SMBus(2 線/I²C),UART/USART
外圍設備: POR,PWM,WDT
輸入/輸出數: 8
程序存儲器容量: 4KB(4K x 8)
程序存儲器類型: 閃存
RAM 容量: 256 x 8
電壓 - 電源 (Vcc/Vdd): 2.7 V ~ 3.6 V
振蕩器型: 外部
工作溫度: -40°C ~ 85°C
封裝/外殼: 10-VFDFN 裸露焊盤
包裝: 帶卷 (TR)
配用: 336-1444-ND - ADAPTER PROGRAM TOOLSTICK F300
Rev. 2.9
101
C8051F300/1/2/3/4/5
11.4. External Crystal Example
If a crystal or ceramic resonator is used as an external oscillator source for the MCU, the circuit should be
configured as shown in Figure 11.1, Option 1. The External Oscillator Frequency Control value (XFCN)
should be chosen from the Crystal column of the table in SFR Definition 11.3 (OSCXCN register). For
example, an 11.0592 MHz crystal requires an XFCN setting of 111b.
When the crystal oscillator is first enabled, the oscillator amplitude detection circuit requires a settling time
to achieve proper bias. Introducing a delay of 1 ms between enabling the oscillator and checking the
XTLVLD bit will prevent a premature switch to the external oscillator as the system clock. Switching to the
external oscillator before the crystal oscillator has stabilized can result in unpredictable behavior. The rec-
ommended procedure is:
Step 1. Force the XTAL1 and XTAL2 pins low by writing 0’s to the port latch.
Step 2. Configure XTAL1 and XTAL2 as analog inputs.
Step 3. Enable the external oscillator.
Step 4. Wait at least 1 ms.
Step 5. Poll for XTLVLD => ‘1’.
Step 6. Switch the system clock to the external oscillator.
Note: Tuning-fork crystals may require additional settling time before XTLVLD returns a valid
result.
The capacitors shown in the external crystal configuration provide the load capacitance required by the
crystal for correct oscillation. These capacitors are “in series” as seen by the crystal and “in parallel” with
the stray capacitance of the XTAL1 and XTAL2 pins.
Note: The load capacitance depends upon the crystal and the manufacturer. Please refer to the
crystal data sheet when completing these calculations.
For example, a tuning-fork crystal of 32.768 kHz with a recommended load capacitance of 12.5 pF should
use the configuration shown in Figure 12.1, Option 1. The total value of the capacitors and the stray capac-
itance of the XTAL pins should equal 25 pF. With a stray capacitance of 3 pF per pin, the 22 pF capacitors
yield an equivalent capacitance of 12.5 pF across the crystal, as shown in Figure 11.2.
Figure 11.2. 32.768 kHz External Crystal Example
22 pF
32.768 kHz
10 M
XTAL1
XTAL2
相關PDF資料
PDF描述
VE-BNL-IW-F3 CONVERTER MOD DC/DC 28V 100W
VE-BNL-IW-F2 CONVERTER MOD DC/DC 28V 100W
VE-BNL-IW-F1 CONVERTER MOD DC/DC 28V 100W
VE-BNK-IX-F4 CONVERTER MOD DC/DC 40V 75W
VE-BNK-IX-F2 CONVERTER MOD DC/DC 40V 75W
相關代理商/技術參數
參數描述
C8051F304-GS 功能描述:8位微控制器 -MCU 4KB Flash RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F304-GSR 功能描述:8位微控制器 -MCU 4KB 14Pin MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F304R 功能描述:8位微控制器 -MCU 303 4Kbyte RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F305 功能描述:8位微控制器 -MCU 2KB RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
C8051F305-GM 功能描述:8位微控制器 -MCU 2KB 11P MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT