FN957.10 July 11, 2005 This circuit can be adjusted most easily with a distortion analyzer, but a good first approximation can be made by compa" />
參數資料
型號: CA3140EZ
廠商: Intersil
文件頁數: 5/23頁
文件大?。?/td> 0K
描述: IC OP AMP 4.5MHZ BIMOS 8-DIP
標準包裝: 50
放大器類型: 通用
電路數: 1
轉換速率: 9 V/µs
增益帶寬積: 4.5MHz
電流 - 輸入偏壓: 10pA
電壓 - 輸入偏移: 5000µV
電流 - 電源: 4mA
電流 - 輸出 / 通道: 40mA
電壓 - 電源,單路/雙路(±): 4 V ~ 36 V,±2 V ~ 18 V
工作溫度: -55°C ~ 125°C
安裝類型: 通孔
封裝/外殼: 8-DIP(0.300",7.62mm)
供應商設備封裝: 8-PDIP
包裝: 管件
13
FN957.10
July 11, 2005
This circuit can be adjusted most easily with a distortion
analyzer, but a good first approximation can be made by
comparing the output signal with that of a sine wave
generator. The initial slope is adjusted with the potentiometer
R1, followed by an adjustment of R2. The final slope is
established by adjusting R3, thereby adding additional
segments that are contributed by these diodes. Because
there is some interaction among these controls, repetition of
the adjustment procedure may be necessary.
Sweeping Generator
Figure 13 shows a sweeping generator. Three CA3140s are
used in this circuit. One CA3140 is used as an integrator, a
second device is used as a hysteresis switch that determines
the starting and stopping points of the sweep. A third
CA3140 is used as a logarithmic shaping network for the log
function. Rates and slopes, as well as sawtooth, triangle,
and logarithmic sweeps are generated by this circuit.
Wideband Output Amplifier
Figure 14 shows a high slew rate, wideband amplifier
suitable for use as a 50
transmission line driver. This
circuit, when used in conjunction with the function generator
and sine wave shaper circuits shown in Figures 10 and 12
provides 18VP-P output open circuited, or 9VP-P output
when terminated in 50
. The slew rate required of this
amplifier is 28V/
s (18V
P-P x π x 0.5MHz).
Power Supplies
High input impedance, common mode capability down to the
negative supply and high output drive current capability are
key factors in the design of wide range output voltage
supplies that use a single input voltage to provide a
regulated output voltage that can be adjusted from
essentially 0V to 24V.
Unlike many regulator systems using comparators having a
bipolar transistor input stage, a high impedance reference
voltage divider from a single supply can be used in
connection with the CA3140 (see Figure 15).
Essentially, the regulators, shown in Figures 16 and 17, are
connected as non inverting power operational amplifiers with a
gain of 3.2. An 8V reference input yields a maximum output
voltage slightly greater than 25V. As a voltage follower, when
the reference input goes to 0V the output will be 0V. Because
the offset voltage is also multiplied by the 3.2 gain factor, a
potentiometer is needed to null the offset voltage.
Series pass transistors with high ICBO levels will also
prevent the output voltage from reaching zero because there
is a finite voltage drop (VCESAT) across the output of the
CA3140 (see Figure 2). This saturation voltage level may
indeed set the lowest voltage obtainable.
The high impedance presented by Terminal 8 is
advantageous in effecting current limiting. Thus, only a small
signal transistor is required for the current-limit sensing
amplifier. Resistive decoupling is provided for this transistor
to minimize damage to it or the CA3140 in the event of
unusual input or output transients on the supply rail.
Figures 16 and 17, show circuits in which a D2201 high speed
diode is used for the current sensor. This diode was chosen
for its slightly higher forward voltage drop characteristic, thus
giving greater sensitivity. It must be emphasized that heat
sinking of this diode is essential to minimize variation of the
current trip point due to internal heating of the diode. That is,
1A at 1V forward drop represents one watt which can result in
significant regenerative changes in the current trip point as the
diode temperature rises. Placing the small signal reference
amplifier in the proximity of the current sensing diode also
helps minimize the variability in the trip level due to the
negative temperature coefficient of the diode. In spite of those
limitations, the current limiting point can easily be adjusted
over the range from 10mA to 1A with a single adjustment
potentiometer. If the temperature stability of the current
limiting system is a serious consideration, the more usual
current sampling resistor type of circuitry should be employed.
A power Darlington transistor (in a metal can with heatsink),
is used as the series pass element for the conventional
current limiting system, Figure 16, because high power
Darlington dissipation will be encountered at low output
voltage and high currents.
2
6
8
1
4
7
+
CA3140
-
50
F
25V
2.2
k
2N3053
1N914
2.2
k
1N914
2.7
2.7
2N4037
+
-
+
- 50F
25V
3
SIGNAL
LEVEL
ADJUSTMENT
2.5k
200
2.4pF
2pF
-15V
+15V
OUTPUT
DC LEVEL
ADJUSTMENT
-15V
+15V
3k
200
1.8k
51
2W
OUT
NOMINAL BANDWIDTH = 10MHz
tr = 35ns
FIGURE 14. WIDEBAND OUTPUT AMPLIFIER
6
3
2
4
7
+
CA3140
-
VOLTAGE
REFERENCE
VOLTAGE
ADJUSTMENT
REGULATED
OUTPUT
INPUT
FIGURE 15. BASIC SINGLE SUPPLY VOLTAGE REGULATOR
SHOWING VOLTAGE FOLLOWER CONFIGURATION
CA3140, CA3140A
相關PDF資料
PDF描述
FTS-140-01-L-DV CONN HEADER 80POS DUAL .05" SMD
FTS-145-01-L-D CONN HEADER 90POS DUAL .05" T/H
TSW-134-26-S-D CONN HEADER 68POS .100" DL GOLD
TMM-143-01-S-S-SM CONN HEADER 43POS SNGL 2MM SMD
AD744KRZ-REEL IC OPAMP BIFET 13MHZ PREC 8SOIC
相關代理商/技術參數
參數描述
CA3140EZ 制造商:Intersil Corporation 功能描述:IC OP-AMP 4.5MHZ 9V/ DIP
CA3140M 功能描述:IC OP AMP BIMOS 4.5MHZ 8-SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源,單路/雙路(±):1.8 V ~ 5.25 V,±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP,10-MSOP(0.118",3.00mm 寬) 供應商設備封裝:10-MSOP 包裝:管件
CA3140M96 功能描述:IC OP AMP 4.5MHZ BIMOS 8-SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源,單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC(0.154",3.90mm 寬) 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT
CA3140MZ 功能描述:運算放大器 - 運放 OPAMP 4.5MHZ LWBIAS RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
CA3140MZ96 功能描述:運算放大器 - 運放 OPAMP 4 5MHZ LWBIAS MILEL RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel