- 您現在的位置：買賣IC網 > PDF目錄366673 > CAT1161JI-25TE13 Supervisory Circuits with I2C Serial CMOS EEPROM, Precision Reset Controller and Watchdog Timer PDF資料下載
參數資料
| 型號： | CAT1161JI-25TE13 |
| 英文描述： | Supervisory Circuits with I2C Serial CMOS EEPROM, Precision Reset Controller and Watchdog Timer |
| 中文描述： | 監控電路，帶有I2C串行CMOS EEPROM的，精密復位控制器和看門狗定時器 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 69K |
| 代理商： | CAT1161JI-25TE13 |
8
CAT1161/2
Doc. No. 3002, Rev. D
ACKNOWLEDGE
After a successful data transfer, each receiving device
is required to generate an acknowledge. The
acknowledging device pulls down the SDA line during
the ninth clock cycle, signaling that it received the 8 bits
of data.
The CAT1161/2 responds with an acknowledge after
receiving a START condition and its slave address. If the
device has been selected along with a write operation,
it responds with an acknowledge after receiving each 8-
bit byte.
When the CAT1161/2 begins a READ mode it transmits
8 bits of data, releases the SDA line and monitors the
line for an acknowledge. Once it receives this
acknowledge, the CAT1161/2 will continue to transmit
data. If no acknowledge is sent by the Master, the device
terminates data transmission and waits for a STOP
condition.
WRITE OPERATIONS
Byte Write
In the Byte Write mode, the Master device sends the
START condition and the slave address information
(with the R/
W
bit set to zero) to the Slave device. After
the Slave generates an acknowledge, the Master sends
a 8-bit address that is to be written into the address
pointers of the CAT1161/2. After receiving another
acknowledge from the Slave, the Master device transmits
the data to be written into the addressed memory location.
The CAT1161/2 acknowledges once more and the Master
generates the STOP condition. At this time, the device
begins an internal programming cycle to non-volatile
memory. While the cycle is in progress, the device will not
respond to any request from the Master device.
Page Write
The CAT1161/2 writes up to 16 bytes of data in a single
write cycle, using the Page Write operation. The page
write operation is initiated in the same manner as the byte
write operation, however instead of terminating after the
initial byte is transmitted, the Master is allowed to send up
to 15 additional bytes. After each byte has been
transmitted, the CAT1161/2 will respond with an
acknowledge and internally increment the lower order
address bits by one. The high order bits remain unchanged.
If the Master transmits more than 16 bytes before sending
the STOP condition, the address counter
‘
wraps around,
’
and previously transmitted data will be overwritten.
When all 16 bytes are received, and the STOP condition
has been sent by the Master, the internal programming
cycle begins. At this point, all received data is written to
the CAT1161/2 in a single write cycle.
BYTE
ADDRESS
SLAVE
ADDRESS
S
A
C
K
A
C
K
DATA
A
C
K
S
T
O
P
P
BUS ACTIVITY:
MASTER
SDA LINE
S
T
A
R
T
Figure 7. Byte Write Timing
Figure 8. Page Write Timing
BUS ACTIVITY:
MASTER
SDA LINE
DATA n+15
BYTE
ADDRESS (n)
A
C
K
A
C
K
DATA n
A
C
K
S
T
O
P
S
A
C
K
DATA n+1
A
C
K
S
T
A
R
T
P
SLAVE
ADDRESS
相關PDF資料 |
PDF描述 |
|---|---|
| CAT1161JI-28TE13 | Supervisory Circuits with I2C Serial CMOS EEPROM, Precision Reset Controller and Watchdog Timer |
| CAT1161JI-30TE13 | Supervisory Circuits with I2C Serial CMOS EEPROM, Precision Reset Controller and Watchdog Timer |
| CAT1161JI-42TE13 | Supervisory Circuits with I2C Serial CMOS EEPROM, Precision Reset Controller and Watchdog Timer |
| CAT1161JI-45TE13 | Supervisory Circuits with I2C Serial CMOS EEPROM, Precision Reset Controller and Watchdog Timer |
| CAT1161P-25TE13 | Supervisory Circuits with I2C Serial CMOS EEPROM, Precision Reset Controller and Watchdog Timer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT1161JI-30 | 功能描述:監控電路 16K I2C Memory w/WDT RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1161JI-42 | 功能描述:監控電路 16K I2C Memory w/WDT RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1161L-25 | 功能描述:監控電路 16K I2C Memory w/WDT RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1161L-42 | 功能描述:監控電路 16K I2C Memory w/WDT RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT1161L-42 | 制造商:ON Semiconductor 功能描述:IC SUPERVISORY CCT W/ 16K E2 |
發布緊急采購，3分鐘左右您將得到回復。