- 您現在的位置：買賣IC網 > PDF目錄223524 > CAT24C21PE 128 X 8 I2C/2-WIRE SERIAL EEPROM, PDIP8 PDF資料下載
參數資料
| 型號： | CAT24C21PE |
| 元件分類： | PROM |
| 英文描述： | 128 X 8 I2C/2-WIRE SERIAL EEPROM, PDIP8 |
| 封裝： | PLASTIC, DIP-8 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 65K |
| 代理商： | CAT24C21PE |
CAT24C21
8
Doc. No. 1032, Rev. N
Figure 10. Page Write Timing
Figure 9. Byte Write Timing
nMAX = 7FH
P = 15 for CAT24WC21
* = Don't care
Write Protection
When the VCLK pin is connected to GND and the
CAT24C21 is in the bi-directional mode, the entire
memory is protected and becomes "read only".
Read Operations
The READ operation for the CAT24C21 is initiated in the
same manner as the write operation with the one
exception that the R/
W bit is set to a one. Three different
READ operations are possible: Immediate Address
READ, Selective READ and Sequential READ.
Immediate Address Read
The CAT24C21’s address counter contains the address
of the last byte accessed, incremented by one. In other
words, if the last READ or WRITE access was to address
N, the READ immediately following would access data
from address N + 1 (Figure 11). If N = 127, then the
counter will 'wrap around' to address 0 and continue to
clock out data.
BUS ACTIVITY:
MASTER
SDA LINE
DATA n+P
BYTE
ADDRESS (n)
A
C
K
A
C
K
DATA n
A
C
K
S
T
O
P
S
A
C
K
DATA n+1
A
C
K
S
T
A
R
T
P
SLAVE
ADDRESS
*
** *
BYTE
ADDRESS
SLAVE
ADDRESS
S
A
C
K
A
C
K
DATA
A
C
K
S
T
O
P
BUS ACTIVITY:
MASTER
SDA LINE
S
T
A
R
T
** *
*
Selective Read
Selective READ operations allow the Master device to
select at random any memory location for a READ
operation (Figure 12). The Master device first performs
a ‘dummy’ write operation by sending the START
condition, slave address and byte address of the location
it wishes to read. After the CAT24C21 acknowledges the
word address, the Master device resends the START
condition and the slave address, this time with the R/
W
bit set to one. The CAT24C21 then responds with its
ACK and sends the 8-bit byte requested. The master
device does not send an ACK but will generate a STOP
condition.
Sequential Read
The Sequential READ operation (Figure 13) can be
initiated by either the Immediate Address READ or the
Selective READ operation. After the CAT24C21 sends
the first 8-bit byte, the Master responds with an ACK,
which tells the Slave that more data is being requested.
The CAT24C21 will continue to output an 8-bit byte for
each ACK sent by the Master. The entire memory
content can thus be read out sequentially. If the end of
memory is reached in the process, then addressing will
'wrap-around' to the beginning of memory. Data output
will stop when the Master fails to acknowledge and
sends a STOP condition.
相關PDF資料 |
PDF描述 |
|---|---|
| CAT24C642JA-42TE13 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO8 |
| CAT24C642PA-30 | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDIP8 |
| CAT24WC08WA | 1K X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| CAT24WC01ZA-TE13 | 128 X 8 I2C/2-WIRE SERIAL EEPROM, PDSO8 |
| CAT25020YE-T3 | 256 X 8 SPI BUS SERIAL EEPROM, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT24C21WGI | 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述: |
| CAT24C21WGI-T3 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述: |
| CAT24C21WI | 功能描述:電可擦除可編程只讀存儲器 1K Dual Mode Serial RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| CAT24C21WI-G | 制造商:Rochester Electronics LLC 功能描述: 制造商:ON Semiconductor 功能描述: |
| CAT24C21WI-GT3 | 功能描述:電可擦除可編程只讀存儲器 1K DUAL MODE SER 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。