- 您現在的位置：買賣IC網 > PDF目錄369655 > CAT4004 4-Channel Constant Current LED Driver with EZDi TM PDF資料下載
參數資料
| 型號： | CAT4004 |
| 英文描述： | 4-Channel Constant Current LED Driver with EZDi TM |
| 中文描述： | 4通道恒定電流LED驅動EZDi商標 |
| 文件頁數： | 7/11頁 |
| 文件大?。?/td> | 276K |
| 代理商： | CAT4004 |
CAT4004
2007 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
7
Doc. No. 5024 Rev. A
PIN DESCRIPTIONS
Pin #
1
2
3
4
5
6
7
8
TAB
Name
EN/DIM
GND
LED1
LED2
LED3
LED4
RSET
VIN
TAB
Function
Device enable (active high) and dimming control
Ground reference
LED1 cathode terminal
LED2 cathode terminal
LED3 cathode terminal
LED4 cathode terminal
RSET external LED mirror gain 128
Device supply input, connect to battery or supply
Connect to GND on the PCB
PIN FUNCTION
VIN
is the supply pin for the charge pump. A small
1
μ
F ceramic bypass capacitor is required between the
VIN pin and ground near the device. The operating
input voltage range is from 2.5V to 5.5V. Whenever
the input supply falls below the under-voltage
threshold (1.8V), all the LED channels are disabled
and the device enters shutdown mode.
EN/DIM
is the enable and one wire dimming input for
all LED channels. Levels of logic high and logic low
are set at 1.3V and 0.4V respectively. When EN/DIM
is initially taken high, the device becomes enabled
and all LED currents are set to the full scale according
to the resistor R
SET
. To place the device into “zero
current” shutdown mode, the EN/DIM pin must be
held low for at least 1.5ms.
LED1 to LED4
provide the internal regulated current
for each of the LED cathodes. There pins enter a high
impedance zero current state whenver the device is
placed in shutdown mode.
RSET
is connected to the resistor (R
SET
) to set the full
scale current for the LEDs. The voltage at this pin is
regulated to 0.6V. The ground side of the external
resistor should be star connected back to the GND of
the PCB. In shutdown mode, RSET beomes high
impedance.
GND
is the ground reference for the device. The pin
must be connected to the ground plane on the PCB.
TAB
is the exposed pad underneath the package. For
best thermal performance, the tab should be soldered
to the PCB and connected to the ground plane.
相關PDF資料 |
PDF描述 |
|---|---|
| CAT4004VP2-T3 | 4-Channel Constant Current LED Driver with EZDi TM |
| CAT4238 | High Efficiency 10 LED Boost Converter |
| CAT4238TD-GT3 | High Efficiency 10 LED Boost Converter |
| CAT5241WI-10 | Quad Digitally Programmable Potentiometers (DPP⑩) with 64 Taps and 2-wire Interface |
| CAT5241 | Quad Digitally Programmable Potentiometers (DPP⑩) with 64 Taps and 2-wire Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT4004_08 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:4-Channel Constant Current LED Driver with EZDim⑩ |
| CAT4004A | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Constant Current LED Driver with 32 Dimming Levels and Rset |
| CAT4004AHU2-GT3 | 功能描述:LED照明驅動器 LED DR 4 CH EZ DIM I/F RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| CAT4004AHU2-GT3B | 功能描述:LED照明驅動器 322.4V to 5.5V RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| CAT4004BHU2-GT3 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Constant Current Programmable LED Driver with 32 Dimming Levels |
發布緊急采購，3分鐘左右您將得到回復。