- 您現在的位置：買賣IC網 > PDF目錄366732 > CAT4237TS High Voltage CMOS Boost White LED Driver PDF資料下載
參數資料
| 型號： | CAT4237TS |
| 英文描述： | High Voltage CMOS Boost White LED Driver |
| 中文描述： | 高電壓的CMOS升壓白光LED驅動器 |
| 文件頁數： | 3/13頁 |
| 文件大小： | 533K |
| 代理商： | CAT4237TS |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
CAT4237
2005 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
3 of 13
Doc. No. 5013, Rev. A
PIN DESCRIPTION
VIN
is the supply input for the internal logic
The device is compatible with supply voltages
down to 2.8V and up to 5.5V. It is
recommended that a small bypass ceramic
capacitor (4.7uF) be placed between the VIN
and GND pins near the device. If the supply
voltage drops below 1.9V, the device stops
switching.
SHDN*
is the shutdown logic input. When the
pin is tied to a voltage lower than 0.4V, the
device is in shutdown mode, drawing nearly
zero current. When the pin is connected to a
voltage higher than 1.5V, the device is
enabled.
GND
is the ground reference pin. This pin
should be connected directly to the ground
place on the PCB.
Pin #
1
2
3
4
5
BLOCK DIAGRAM
SW
pin is connected to the drain of the internal
CMOS power switch of the boost converter. The
inductor and the Schottky diode anode should be
connected to the SW pin. Traces going to the SW
pin should be as short as possible with minimum
loop area. An over-voltage detection circuit is
connected to the SW pin. When the voltage
reaches 35V, the device enters a low power
operating mode preventing the SW voltage from
exceeding the maximum rating.
FB
feedback pin is regulated at 0.3V. A resistor
connected between the FB pin and ground sets
the LED current according to the formula:
I
LED
= 0.3V/R1
The lower LED cathode is connected to the FB pin.
Name
SW
GND
FB
SHDN*
VIN
Function
Switch pin. This is the drain of the internal power switch.
Ground pin. Connect the pin to the ground plane.
Feedback pin. Connect to the last LED cathode.
Shutdown pin (Logic Low). Set high to enable the driver.
Power Supply input.
相關PDF資料 |
PDF描述 |
|---|---|
| CAT4240 | 6 Watt Boost LED Driver |
| CAT4240TD-GT3 | 6 Watt Boost LED Driver |
| CAT507BP | 3.3V 32K/64K x 16/18 Dual-Port Static RAM |
| CAT504J | 8-Bit Digital-to-Analog Converter |
| CAT504JI | 8-Bit Digital-to-Analog Converter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT4237TS-TE7 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述: |
| CAT4238 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High Efficiency 10 LED Boost Converter |
| CAT4238_07 | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:High Efficiency 10 LED Boost Converter |
| CAT4238AEVB | 功能描述:BOARD EVALUATION DPP CAT4238A RoHS:是 類別:編程器，開發系統 >> 評估板 - LED 驅動器 系列:* 標準包裝:1 系列:PowerWise® 電流 - 輸出 / 通道:20mA 輸出及類型:1，非隔離 輸出電壓:17V 特點:可調光 輸入電壓:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相關產品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| CAT4238AGEVB | 功能描述:BOARD EVALUATION DPP CAT4238A 制造商:on semiconductor 系列:- 零件狀態:在售 電流 - 輸出/通道:40mA 輸出和類型:1，非隔離 電壓 - 輸出:- 特性:可調光 電壓 - 輸入:2.8 V ~ 5.5 V 所含物品:板 使用的 IC/零件:CAT4238 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。