參數資料
型號: CAT5110TBI-50-T3
元件分類: 數字電位計
英文描述: 32-Tap MiniPot⑩ Digitally Programmable Potentiometers with 2-Wire Interface
中文描述: 32抽頭的2線接口MiniPot⑩數字可編程電位器
文件頁數: 5/16頁
文件大?。?/td> 694K
代理商: CAT5110TBI-50-T3
CAT5110, CAT5118, CAT5119, CAT5123, CAT5124, CAT5125
5
Doc No. MD-220, Rev. F
Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
CS
U/D
W
t
CU
t
IL
t
IH
t
SETTLE
t
IC
t
CI
t
SETTLE
Note: "W" is not a digital signal. It represents wiper transitions.
FunCTIOnAl DesCrIPTIOn
The CAT50/58/59/523/524/525 consist of
a fixed resistor and a wiper contact with 32-tap points
that are digitally controlled through a 2-wire up/down
serial interface. Three end-to-end resistance values are
available: 0k
Ω
, 50k
Ω
and 00k
Ω
.
The CAT50/525 is designed to operate as a
potentiometer. In this configuration, the low terminal of
the resistor array is connected to ground (pin 2).
The CAT58/523 performs as a variable resistor. In
this device, the wiper terminal and high terminal of the
resistor array are connected at pin 5. The CAT59/524
is a similar variable resistor, except the low terminal is
connected to pin 5.
DIGITAl InTerFACe OPerATIOn
The MiniPots have two modes of operation when the
serial interface is active: increment and decrement mode.
The serial interface is only active when CS is low.
Figure 2. serial Interface Timing Diagram, Decrement Mode
Figure 1. serial Interface Timing Diagram, Increment Mode
The CS and U/D inputs control the position of the wiper
along the resistor array. When CS transitions from high
to low, the part will go into increment mode if U/D input
is high, and into decrement mode when U/D input is low.
Once the mode is set, the device will remain in that mode
until CS goes high again. A low-to-high transition at the
U/D pin will increment or decrement the wiper position
depending on the current mode (Figures and 2).
When the CS input transitions to high (serial interface
inactive), the value of the counter is stored and the wiper
position is maintained.
Note that when the wiper reaches the maximum (or
minimum) tap position, the wiper will not wrap around
to the minimum (or maximum) position.
POWer-On reseT
All parts in this family feature power-on reset (POR)
circuitry that sets the wiper position to midscale at power-
up. By default, the chip is in the increment mode.
CS
U/D
W
t
CU
t
IL
t
IH
t
IC
t
SETTLE
t
CI
t
SETTLE
Note: "W" is not a digital signal. It represents wiper transitions.
相關PDF資料
PDF描述
CAT5110SDI-50-GT3 32-Tap MiniPot⑩ Digitally Programmable Potentiometers with 2-Wire Interface
CAT5110TBI-00-GT10 32-Tap MiniPot⑩ Digitally Programmable Potentiometers with 2-Wire Interface
CAT5110TBI-00-GT3 32-Tap MiniPot⑩ Digitally Programmable Potentiometers with 2-Wire Interface
CAT5110TBI-00-T3 32-Tap MiniPot⑩ Digitally Programmable Potentiometers with 2-Wire Interface
CAT5110TBI-10-GT10 32-Tap MiniPot⑩ Digitally Programmable Potentiometers with 2-Wire Interface
相關代理商/技術參數
參數描述
CAT5110TPI-00-T 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:32-Tap MiniPot Digitally Programmable Potentiometers with 2-Wire Interface
CAT5110TPI-00-T10 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:32-Tap MiniPot Digitally Programmable Potentiometers with 2-Wire Interface
CAT5110TPI-10 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述:
CAT5110TPI-10-T 制造商:Rochester Electronics LLC 功能描述: 制造商:Catalyst Semiconductor 功能描述:
CAT5110TPI-10-T10 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:32-Tap MiniPot Digitally Programmable Potentiometers with 2-Wire Interface