參數資料
型號： CAT5114PI-50TE13
元件分類： 數字電位計
英文描述： 32-Tap Digitally Programmable Potentiometer
中文描述： 32抽頭數字可編程電位器
文件頁數： 2/7頁
文件大小： 61K
代理商： CAT5114PI-50TE13
CAT5112
2
Doc. No. 2002, Rev. L
of the CAT5112 and is active low. When in a high
state, activity on the
INC
and U/
D
inputs will not
affect or change the position of the wiper.
DEVICE OPERATION
The CAT5112 operates like a digitally controlled
potentiometer with R
H
and R
L
equivalent to the high
and low terminals and R
WB
equivalent to the mechanical
potentiometer's wiper. There are 32 available tap posi-
tions including the resistor end points, R
H
and R
L
. There
are 31 resistor elements connected in series between
the R
H
and R
L
terminals. The wiper terminal is
connected to one of the 32 taps and controlled by three
inputs,
INC
, U/
D
and
CS
. These inputs control a five-bit
up/down counter whose output is decoded to select the
wiper position. The selected wiper position can be
stored in nonvolatile memory using the
INC
and
CS
inputs.
With
CS
set LOW the CAT5112 is selected and will
respond to the U/
D
and
INC
inputs. HIGH to LOW
transitions on
INC
wil increment or decrement the
wiper (depending on the state of the U/
D
input and five-
bit counter). The wiper, when at either fixed terminal,
acts like its mechanical equivalent and does not move
beyond the last position. The value of the counter is
stored in nonvolatile memory whenever
CS
transitions
HIGH while the
INC
input is also HIGH. When the
CAT5112 is powered-down, the last stored wiper counter
position is maintained in the nonvolatile memory. When
power is restored, the contents of the memory are
recalled and the counter is set to the value stored.
With
INC
set low, the CAT5112 may be de-selected
and powered down without storing the current wiper
position in nonvolatile memory. This allows the
system to always power up to a preset value stored
in nonvolatile memory.
PIN DESCRIPTIONS
INC
: Increment Control Input
The
INC
input (on the falling edge) moves the wiper in the
up or down direction determined by the condition of the
U/
D
input.
U/
D
: Up/Down Control Input
The U/
D
input controls the direction of the wiper
movement. When in a high state and
CS
is low, any high-
to-low transition on
INC
will cause the wiper to move one
increment toward the R
H
terminal. When in a low state
and
CS
is low, any high-to-low transition on
INC
will
cause the wiper to move one increment towards the
R
L
terminal.
R
H:
High End Potentiometer Terminal
R
H
is the high end terminal of the potentiometer. It is not
required that this terminal be connected to a potential
greater than the R
L
terminal. Voltage applied to the R
H
terminal cannot exceed the supply voltage, V
CC
or go
below ground, GND.
R
WB
: Wiper Potentiometer Terminal (Buffered)
R
WB
is the buffered wiper terminal of the potentiometer. Its
position on the resistor array is controlled by the control
inputs,
INC
, U/
D
and
CS
.
R
L
: Low End Potentiometer Terminal
R
L
is the low end terminal of the potentiometer. It is not
required that this terminal be connected to a potential
less than the R
H
terminal. Voltage applied to the R
L
terminal cannot exceed the supply voltage, V
CC
or go
below ground, GND. R
L
and R
H
are electrically
interchangeable.
CS
: Chip Select
The chip select input is used to activate the control input
PIN FUNCTIONS
Pin Name
Function
INC
Increment Control
U/
D
Up/Down Control
R
H
Potentiometer High Terminal
GND
Ground
R
WB
Buffered Wiper Terminal
R
L
Potentiometer Low Terminal
CS
Chip Select
V
CC
Supply Voltage
PIN CONFIGURATION
PDIP Package (P, L)
TSSOP Package (U, Y)
MSOP Package (R, Z)
INC
U
/D
V
CC
CS
RL
RWB
GND
RH
1
2
3
4
8
7
6
5
CS
RL
RWB
INC
U
/D
RH
GND
V
CC
1
2
3
4
8
7
6
5
V
CC
CS
RL
RWB
GND
RH
INC
U/
D
1
2
3
4
8
7
6
5
CS
RL
RWB
INC
U
/D
RH
GND
V
CC
1
2
3
4
8
7
6
5
SOIC Package (S, V)
相關PDF資料
PDF描述
CAT5114R00TE13 32-Tap Digitally Programmable Potentiometer
CAT5114R10TE13 32-Tap Digitally Programmable Potentiometer
CAT5114R50TE13 32-Tap Digitally Programmable Potentiometer
CAT5113LI-10-G 100-Tap Digitally Programmable Potentiometer (DPP⑩)
CAT5113LI-50-G 100-Tap Digitally Programmable Potentiometer (DPP⑩)
相關代理商/技術參數
參數描述
CAT5114R-00 功能描述:數字電位計 IC Com Temp 100K Up/Dwn RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
CAT5114R-10 功能描述:數字電位計 IC Com Temp 10K Up/Dwn RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
CAT5114RI-00 功能描述:數字電位計 IC Ind Temp 100K Up/Dwn RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
CAT5114RI00-TE13 制造商:ON Semiconductor 功能描述:Digital Potentiometer 32POS 100KOhm Single 8-Pin MSOP T/R
CAT5114RI-10 功能描述:數字電位計 IC Ind Temp 10K Up/Dwn RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*