- 您現在的位置：買賣IC網 > PDF目錄223525 > CAT825TSDI-GT3 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 PDF資料下載
參數資料
| 型號： | CAT825TSDI-GT3 |
| 元件分類： | 電源管理 |
| 英文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| 封裝： | ROHS COMPLIANT, MO-203, SC-70, 5 PIN |
| 文件頁數： | 2/14頁 |
| 文件大小： | 209K |
| 代理商： | CAT825TSDI-GT3 |
CAT823, CAT824, CAT825
Doc. No. MD-3027 Rev. B
10
Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
APPLICATION NOTES
P’s with Bidirectional Reset Pins
The RESET
output can be pulled low by processors
like the 68HC11 allowing for a system reset issued by
the processor. The maximum pullup current that can
be sourced by the CAT82_L/M is 1.5mA (and by the
CAT82_T/R/S/Z/Y is 800A) allowing the processor to
pull the output low even when the CAT82x is pulling it
high.
Power Transients
Generally short duration negative-going transients of
less than 2s on the power supply at VRST minimum
will not cause a reset condition. However the lower
the voltage of the transient the shorter the required
time to cause a reset output.
These issues can
usually be remedied by the proper location of bypass
capacitance on the circuit board.
OUTPUT VALID CONDITIONS
The RESET
output uses a push-pull output which can
maintain a valid output down to a VCC of 1.0 volts. To
sink current below 0.8V a resistor can be connected
from RESET
to Ground (see Figure 8.)
This
arrangement will maintain a valid value on the RESET
output during both power up and down but will draw
current when the RESET
output is in the high state. A
resistor value of about 100k should be adequate in
most situations to maintain a low condition valid
output down to VCC equal to 0V.
Figure 8. RESET
Valid to 0 Volts VCC
100k
CAT823
VCC
GND
WDI
MR
C
RESET
相關PDF資料 |
PDF描述 |
|---|---|
| CAT825STDI-G | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| CAT869STBI-GT10 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| CAT863TTBI-GT10 | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO3 |
| CAT93C56AK-TE13 | 128 X 16 MICROWIRE BUS SERIAL EEPROM, PDSO8 |
| CAT93C56API-2.7 | 128 X 16 MICROWIRE BUS SERIAL EEPROM, PDIP8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CAT825TTDI-G | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:System Supervisory Voltage Reset with Watchdog and Manual Reset |
| CAT825TTDI-GT3 | 功能描述:監控電路 act low act hi/MR RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT825YSDI-G | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:System Supervisory Voltage Reset with Watchdog and Manual Reset |
| CAT825YSDI-GT3 | 功能描述:監控電路 SUP ACT LOW ACT HI MR RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| CAT825YTDI-G | 制造商:CATALYST 制造商全稱:Catalyst Semiconductor 功能描述:System Supervisory Voltage Reset with Watchdog and Manual Reset |
發布緊急采購，3分鐘左右您將得到回復。