World Modem NET Page 24 of 64 2005 Copeland Communications, Inc. World Modem NET Datasheet Rev 1.0 Extended AT& Command Set (Comma" />
參數資料
型號： CC-56K2N-CS5
廠商： Copeland Communications Inc
文件頁數： 17/64頁
文件大?。?/td> 0K
描述： MODEM 56KBAUD SERIAL 5V
標準包裝： 30
數據格式： V.22，V23，V.32，V.34，V.90，Bell 103，Bell 212A
波特率： 56k
電源電壓： 4.2 V ~ 7 V
安裝類型： 表面貼裝
封裝/外殼： 模塊
包裝： 散裝
其它名稱： 539-1012
Data Sheet
World Modem NET
Page 24 of 64
2005 Copeland Communications, Inc.
World Modem NET Datasheet Rev 1.0
Extended AT& Command Set (Command Defaults in Bold) (Continued)
Command
Action
&H7
ITU-T V.22 only (1200 bps)
&H8
Bell 212 only (1200 bps)
&H9
Bell 103 only (300 bps)
&H10
ITU-T V.21 only (300 bps)
&H11
V.23 (1200/75 bps)
&Pn
Japan pulse dialing
&P0
Configure modem for 10 pulse-per-second pulse dialing (Japan)
&P1
Configure modem for 20 pulse-per-second pulse dialing (Japan)
&Tn
Test mode
&T0
Cancel test mode (Escape to command mode to issue AT&T0). This command will also report the
number of bit errors encountered on the previous &T4 test.
&T2
Initiate ITU-T V.54 (ANALOOP) test. Modulation set by &H AT command. Test loop is through the
DSP (CC-14.4K2/CC-33K2/CC-56K2 only). The modem echoes data from TX pin back to RX pin.
&T3
Initiate ITU-T V.54 (ANALOOP) test. Modulation set by &H AT command. Test loop is through the
DSP, DAA interface section, DAA interface and analog hybrid circuit. The modem echoes data
from TX pin back to RX pin.
Initiate transmit as originating modem with automatic data generation. Modulation, data rate and
symbol rate are set by &H, &G and S41. Data pattern is set by the S40 register. Continues until
the ATH command is sent after an escape into command mode.
&T4
Data is also demodulated as in ANALOOP, and any bit errors are counted to be displayed after the
test using &T0.
Initiate transmit as answering modem with automatic data generation. Modulation, data rate, and
symbol rate are set by &H, &G and S41. Data pattern is set by the S40 register. Continues until
ATH command is sent after escape into command mode.
&T5
Data is also demodulated as in ANALOOP, and any bit errors are counted to be displayed after the
test using &T0.
&T6
Compute checksum for firmware-upgradeable section of program memory. If no firmware upgrade
is installed, &T6 returns 0x0408.
&Xn
Automatic determination of telephone line type.
&X0
Abort &x1 or &x2 command
相關PDF資料
PDF描述
CC-2404K2N-CS5 MODEM 2400BAUD SERIAL 5V
SI3015-BS IC ISOMODEM LINE-SIDE DAA 16SOIC
PIC16C54T-XTE/SO IC MCU OTP 512X12 18SOIC
PIC16C54T-RC/SS IC MCU OTP 512X12 20SSOP
VE-262-IX-F2 CONVERTER MOD DC/DC 15V 75W
相關代理商/技術參數
參數描述
CC57434 制造商: 功能描述: 制造商:undefined 功能描述:
CC5751-000 制造商:TE Connectivity 功能描述:TWTMS-1/8-NO.11-1-CS5004 - Bulk
CC5872-000 制造商:TE Connectivity 功能描述:100A0111-18-54-CA
CC58C-05 制造商:L-com Inc 功能描述:CABLE ASSEMBLY RG58C BNC M/M 制造商:L-com Inc 功能描述:CABLE ASSEMBLY, RG58C, BNC M/M, 0.5FT 制造商:L-com Inc 功能描述:CABLE ASSEMBLY, RG58C, BNC M/M, 0.5FT; Coaxial Cable Type:RG58C; Impedance:50ohm; Cable Length - Imperial:6"; Cable Length - Metric:150mm; Connector Type A:BNC Straight Plug; Connector Type B:BNC Straight Plug; Jacket Color:Black ;RoHS Compliant: Yes
CC58C-1 制造商:L-com Inc 功能描述:RG58C CABLE, BNC MALE/MALE, 1.0FT 制造商:L-COM 功能描述:CA BNC M/BNC M RG58C/U 1' COAXIAL CABLING
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*