- 您現在的位置：買賣IC網 > PDF目錄16993 > CDB5525 (Cirrus Logic Inc)EVAL BOARD FOR CS5525 PDF資料下載
參數資料
| 型號： | CDB5525 |
| 廠商： | Cirrus Logic Inc |
| 文件頁數： | 6/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | EVAL BOARD FOR CS5525 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 606 |
| 數據接口： | 串行 |
| 輸入范圍： | 0 ~ 5 V |
| 在以下條件下的電源（標準）： | 9.4mW @ 15SPS，5 V |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | CS5525 |
| 已供物品： | 板，CD |
| 相關產品： | CS5525-ASZR-ND - IC ADC 16BIT W/4BIT LATCH 20SSOP 598-1107-5-ND - IC ADC 16BIT W/4BIT LATCH 20SSOP |
| 其它名稱： | 598-1013 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
CS5525 CS5526
14
DS202F5
Analog Input
Figure 7 illustrates a block diagram of the analog in-
put signal path inside the CS5525/26. The front end
consists of a chopper-stabilized instrumentation am-
plifier with 20X gain and a programmable gain sec-
tion. The instrumentation amplifier is powered from
VA+ and from the NBV (Negative Bias Voltage) pin
allowing the CS5525/26 to be operated in either of
two analog input configurations. The NBV pin can
be biased to a negative voltage between -1.8 V and
-2.5 V, or tied to AGND. The choice of the operating
mode for the NBV voltage depends upon the input
signal and its common mode voltage.
For the 25 mV, 55 mV, and 100 mV input ranges, the
input signals to AIN+ and AIN- are amplified by the
20X instrumentation amplifier. For ground refer-
enced signals with magnitudes less then 100 mV, the
NBV pin should be biased with -1.8 V to -2.5 V. If
NBV is tied between -1.8 V and -2.5 V, the (Com-
mon Mode + Signal) input on AIN+ and AIN- must
stay between -0.150 V and 0.950 V to ensure prop-
er operation. Alternatively, NBV can be tied to
AGND where the input (Common Mode + Signal)
on AIN+ and AIN- must stay between 1.85 V and
2.65 V to ensure that the amplifier operates prop-
erly.
For the 1 V, 2.5 V, and 5 V input ranges, the instru-
mentation amplifier is bypassed and the input sig-
nals are directly connected to the Programmable
Gain block. With NBV tied between -1.8 V and
-2.5 V, the (Common Mode + Signal) input on
AIN+ and AIN- must stay between NBV and VA+.
Alternatively, NBV can be tied to AGND where
the input (Common Mode + Signal) on AIN+ and
AIN- pins can span the entire range between
AGND and VA+.
The CS5525/26 can accommodate full scale ranges
other than 25 mV, 55 mV, 100 mV, 1 V, 2.5 V and
5 V by performing a system calibration within the
limits specified. See the Calibration section for
more details. Another way to change the full scale
range is to increase or to decrease the voltage refer-
ence to other than 2.5 V. See the Voltage Refer-
ence section for more details.
Three factors set the operating limits for the input
span. They include: instrumentation amplifier satu-
ration, modulator 1’s density, and a lower reference
voltage. When the 25 mV, 55 mV or 100 mV range
is selected, the input signal (including the common
mode voltage and the amplifier offset voltage)
must not cause the 20X amplifier to saturate in ei-
ther its input stage or output stage. To prevent sat-
uration the absolute voltages on AIN+ and AIN-
must stay within the limits specified (refer to the
‘Analog Input’ table on page 3). Additionally, the
differential output voltage of the amplifier must not
exceed 2.8 V. The equation
ABS(VIN + VOS) x 20 = 2.8 V
defines the differential output limit, where
VIN = (AIN+) - (AIN-)
is the differential input voltage and VOS is the ab-
solute maximum offset voltage for the instrumenta-
tion amplifier (VOS will not exceed 40 mV). If the
VR EF +
D ifferen tial 4th
ord er d elta-
s igm a m o d ula tor
D ig ita l F ilter
AIN +
AIN -
Pro g ra m m a b le
Ga in
VR EF -
NBV
X2 0
Figure 7. Block Diagram of Analog Signal Path
相關PDF資料 |
PDF描述 |
|---|---|
| 222A111-25/86-0 | BOOT MOLDED |
| VI-J0Z-EY | CONVERTER MOD DC/DC 2V 20W |
| CDB5526 | EVAL BOARD FOR CS5526 |
| 1025R-40K | COIL 6.8UH MOLDED UNSHIELDED |
| 222A111-4/86-0 | BOOT MOLDED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| CDB5526 | 功能描述:EVAL BOARD FOR CS5526 RoHS:否 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| CDB5528 | 制造商:CIRRUS 制造商全稱:Cirrus Logic 功能描述:Evaluation Board and Software |
| CDB5529 | 功能描述:EVAL BOARD FOR CS5529 RoHS:否 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| CDB5530U | 功能描述:數據轉換 IC 開發工具 Eval Bd 24-Bit 1-Ch Low-Noise ADC RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| CDB5532U | 功能描述:數據轉換 IC 開發工具 Eval Bd 24Bit ADC w/ Ultra Low-Noise USB RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。