- 您現在的位置：買賣IC網 > PDF目錄352817 > COP840CP-4 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | COP840CP-4 |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 25/26頁 |
| 文件大?。?/td> | 352K |
| 代理商： | COP840CP-4 |
COP620C/COP622C/COP640C/COP642C
Absolute Maximum Ratings (Note 13)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage (V
CC)6V
Voltage at any Pin
0.3V to V
CC + 0.3V
Total Current into V
CC Pin (Source)
40 mA
Total Current out of GND Pin (Sink)
48 mA
Storage Temperature Range
65C to +140C
Note 13:
Absolute maximum ratings indicate limits beyond which damage to
the device may occur. DC and AC electrical specifications are not ensured
when operating the device at absolute maximum ratings.
DC Electrical Characteristics
COP62XC, COP64XC; 55C
≤ T
A ≤ +125C unless otherwise specified
Parameter
Condition
Min
Typ
Max
Units
Operating Voltage
4.5
5.5
V
Power Supply Ripple (Note 14)
Peak to Peak
0.1 V
CC
V
Supply Current (Note 15)
CKI = 10 MHz
V
CC = 5.5V, tc = 1 s
6.0
mA
CKI = 4 MHz
V
CC = 5.5V, tc = 2.5 s
4
mA
HALT Current (Note 16)
V
CC = 5.5V, CKI = 0 MHz
<10
30
A
Input Levels
RESET , CKI
Logic High
0.9 V
CC
V
Logic Low
0.1 V
CC
V
All Other Inputs
Logic High
0.7 V
CC
V
Logic Low
0.2 V
CC
V
Hi-Z Input Leakage
V
CC = 5.5V
5
+5
A
Input Pullup Current
V
CC = 4.5V, VIN = 0V
35
300
A
G Port Input Hysteresis
0.35 V
CC
V
Output Current Levels
D Outputs
Source
V
CC = 4.5V, VOH = 3.8V
0.35
mA
Sink
V
CC = 4.5V, VOL = 1.0V
9
mA
All Others
Source (Weak Pull-Up)
V
CC = 4.5V, VOH = 3.2V
9
120
A
Source (Push-Pull Mode)
V
CC = 4.5V, VOH = 3.8V
0.35
mA
Sink (Push-Pull Mode)
V
CC = 4.5V, VOL = 0.4V
1.4
mA
TRI-STATE Leakage
5.0
+5.0
A
Allowable Sink/Source
Current Per Pin
D Outputs (Sink)
12
mA
All Others
2.5
mA
Maximum Input Current (Room Temp)
Without Latchup (Note 18)
Room Temp
±100
mA
RAM Retention Voltage, Vr
500 ns Rise and Fall Time
(Min)
2.5
V
Input Capacitance
7pF
Load Capacitance on D2
1000
pF
Note 14: Rate of voltage change must be less than 0.5V/ms.
Note 15: Supply current is measured after running 2000 cycles with a square wave CKI input, CKO open, inputs at rails and outputs open.
Note 16: The HALT mode will stop CKI from oscillating in the RC and the Crystal configurations. Test conditions: All inputs tied to VCC, L and G0 — G5 configured
as outputs and set high. The D port set to zero.
Note 17: Except pin G7: +100 mA, 25 mA (COP620C only). Sampled and not 100% tested. Pins G6 and RESET are designed with a high voltage input network
for factory testing. These pins allow input voltages greater than VCC and the pins will have sink current to VCC when biased at voltages greater than VCC (the pins
do not have source current when biased at a voltage below VCC). The effective resistance to VCC is 750 (typical). These two pins will not latch up. The voltage at
the pins must be limited to less than 14V.
COP820C/COP840C
www.national.com
8
相關PDF資料 |
PDF描述 |
|---|---|
| COP840CP-5 | 8-BIT MICROCONTROLLER |
| COP8742CWM | 8-BIT MICROCONTROLLER |
| COP8781CMC | 8-BIT MICROCONTROLLER |
| COP8782CMC | 8-BIT MICROCONTROLLER |
| COP8784CFN-R | 8-BIT MICROCONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP840CP-5 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| COP840C-TKI/N | 制造商:Texas Instruments 功能描述: 制造商:National Semiconductor Corporation 功能描述: |
| COP840C-XXX/D | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based Microcontrollers with 1k or 2k |
| COP840C-XXX/N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| COP840C-XXX/V | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
發(fā)布緊急采購，3分鐘左右您將得到回復。