- 您現在的位置：買賣IC網 > PDF目錄3798 > COP8SAC728M9 (National Semiconductor)IC MCU OTP 8BIT 4K 28SOIC PDF資料下載
參數資料
| 型號： | COP8SAC728M9 |
| 廠商： | National Semiconductor |
| 文件頁數： | 31/62頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU OTP 8BIT 4K 28SOIC |
| 標準包裝： | 26 |
| 系列： | COP8™ 8SA |
| 核心處理器： | COP8 |
| 芯體尺寸： | 8-位 |
| 速度： | 10MHz |
| 連通性： | Microwire/Plus（SPI） |
| 外圍設備： | POR，PWM，WDT |
| 輸入/輸出數： | 24 |
| 程序存儲器容量： | 4KB（4K x 8） |
| 程序存儲器類型： | OTP |
| RAM 容量： | 128 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 振蕩器型： | 內部 |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 包裝： | 管件 |
| 其它名稱： | *COP8SAC728M9 COP8SAC728M9B |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
11.0 MICROWIRE/PLUS
MICROWIRE/PLUS is a serial SPI compatible synchronous
communications interface. The MICROWIRE/PLUS capabil-
ity enables the device to interface with MICROWIRE/PLUS
or SPI peripherals (i.e. A/D converters, display drivers, EE-
PROMs etc.) and with other microcontrollers which support
the MICROWIRE/PLUS or SPI interface. It consists of an
8-bit serial shift register (SIO) with serial data input (SI),
serial data output (SO) and serial shift clock (SK).
Figure 24
shows a block diagram of the MICROWIRE/PLUS logic.
The shift clock can be selected from either an internal source
or an external source. Operating the MICROWIRE/PLUS
arrangement with the internal clock source is called the
Master
mode
of
operation.
Similarly,
operating
the
MICROWIRE/PLUS arrangement with an external shift clock
is called the Slave mode of operation.
The CNTRL register is used to configure and control the
MICROWIRE/PLUS mode. To use the MICROWIRE/PLUS,
the MSEL bit in the CNTRL register is set to one. In the
master mode, the SK clock rate is selected by the two bits,
SL0 and SL1, in the CNTRL register.
Table 9 details the
different clock rates that may be selected.
TABLE 9. MICROWIRE/PLUS
Master Mode Clock Select
SL1
SL0
SK Period
0
2xt
C
0
1
4xt
C
1
x
8xt
C
Where tC is the instruction cycle clock
11.1 MICROWIRE/PLUS OPERATION
Setting the BUSY bit in the PSW register causes the
MICROWIRE/PLUS to start shifting the data. It gets reset
when eight data bits have been shifted. The user may reset
the BUSY bit by software to allow less than 8 bits to shift. If
enabled, an interrupt is generated when eight data bits have
been shifted. The device may enter the MICROWIRE/PLUS
mode either as a Master or as a Slave.
Figure 24 shows how
two microcontroller devices and several peripherals may be
interconnected using the MICROWIRE/PLUS arrangements.
WARNING
The SIO register should only be loaded when the SK clock is
in the idle phase. Loading the SIO register while the SK clock
is in the active phase, will result in undefined data in the SIO
register.
Setting the BUSY flag when the input SK clock is in the
active phase while in the MICROWIRE/PLUS is in the slave
mode may cause the current SK clock for the SIO shift
register to be narrow. For safety, the BUSY flag should only
be set when the input SK clock is in the idle phase.
11.1.1 MICROWIRE/PLUS Master Mode Operation
In the MICROWIRE/PLUS Master mode of operation the
shift clock (SK) is generated internally. The MICROWIRE
Master always initiates all data exchanges. The MSEL bit in
the CNTRL register must be set to enable the SO and SK
functions onto the G Port. The SO and SK pins must also be
selected as outputs by setting appropriate bits in the Port G
configuration register. In the slave mode, the shift clock
stops after 8 clock pulses.
Table 10 summarizes the bit
settings required for Master mode of operation.
DS012838-32
FIGURE 24. MICROWIRE/PLUS Application
COP8SA
Family
www.national.com
36
相關PDF資料 |
PDF描述 |
|---|---|
| COP8SAC720N9 | IC MCU OTP 8BIT 4K 20DIP |
| COP8SAC720M9 | IC MCU OTP 8BIT 4K 20-SOIC |
| P87LPC764BD,512 | IC 80C51 MCU 4K OTP 20-SOIC |
| COP8SAB720N9 | IC MCU OTP 8BIT 2K 20DIP |
| COP8SAB720M9 | IC MCU OTP 8BIT 2K 20SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| COP8SAC728N7 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:8-Bit CMOS ROM Based and One-Time Programmable OTP Microcontroller with 1k to 4k Memory, Power On Reset, and Very Small Packaging |
| COP8SAC728N8 | 制造商:Texas Instruments 功能描述:IC MCU OTP 8BIT 4K 28DIP |
| COP8SAC728N8/NOPB | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| COP8SAC728N9 | 功能描述:IC MCU OTP 8BIT 4K 28DIP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:COP8™ 8SA 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C，IrDA，LIN，SPI，UART/USART 外圍設備:DMA，PDR，POR，PVD，PWM，溫度傳感器，WDT 輸入/輸出數:26 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN，36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND |
| COP8SAC728N9 | 制造商:Texas Instruments 功能描述:IC 8BIT MCU OTP 4K 8SAC728 DIP28 |
發布緊急采購，3分鐘左右您將得到回復。